Vue éclatée Fischer mrp216518b
Découvrez la vue éclatée complète Fischer mrp216518b, un guide indispensable pour identifier facilement toutes les pièces détachées de votre appareil. Que vous soyez à la recherche d'une pièce en particulier ou simplement pour vous aider à la réparation, notre présentation détaillée vous aide à comprendre chaque composant de. Optimisez la maintenance et la réparation de votre appareil grâce à des schémas précis et des références adaptées. Trouvez rapidement les pièces qu'il vous faut pour prolonger la durée de vie de votre Fischer mrp216518b et éviter les pannes imprévues.
Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
1 HANDLE, Upper used on All
Position : 1
1 ASSEMBLY, Right Wheel Arm (Consists of items 2, 3, 4, 5A &
Position : 1
2 BALL BEARING, 9/16” I.D.
Position : 1
1 BELT, Poly-Vee
Position : 1
1 NUT, 5/16-24 Hex Lock
Position : 1
2 WHEEL, 8 x 1.75 Plastic
Position : 1
2 WHEEL, 10 x 1.75” Plastic (Push Models)
Position : 1
1 GRASS BAG, Slider Type (Black)
Position : 1
1 DECAL, Speed Sector
Position : 1
2 LATCH, Frame Attachment
Position : 1
1 SCREEN, Fastener Assembly
Position : 1
1 COVER, 21” Deck
Position : 1
1 PLUG, Chute Adapter
Position : 1
1 HANDLE, Middle used on All
Position : 2
10 NUT, 5/16-18 Hex Flange Lock, GR5
Position : 2
2 BOLT, 5/16-18 Hex Washer Face Shoulder
Position : 2
6 SCREW, #10-32 x 3/8” Hex Washer Self-Tap (Torx head)
Position : 2
1 LINK, Differential (Commercial)
Position : 2
1 WASHER, Bellville
Position : 2
2 PLUG, Wheel
Position : 2
2 WHEEL, 10 x 1.75” Plastic (Self-Propelled Models)
Position : 2
1 ADAPTER, Grass Bag
Position : 2
1 ASSEMBLY, Slider
Position : 2
1 DECAL, Speed Sector Int'l Symbol
Position : 2
1 RING, Bottom
Position : 2
1 BLADE, 21” Quad Edge Ninja
Position : 2
1 HANDLE, Lower LH (Adjustable) used on All
Position : 3
9 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
Position : 3
2 LATCH, Height
Position : 3
2 LATCH, Height Adjusting (Long)
Position : 3
1 ARM, Clutch Idler
Position : 3
1 PULLEY, Poly-Vee Belt
Position : 3
2 NUT, 7/16-20 Hex Center Lock Jam
Position : 3
1 COVER, Bag Adapter
Position : 3
1 CONNECTOR, Grass Bag (weldment)
Position : 3
1 DECAL, Chute/Deflector
Position : 3
2 ROD, Tine
Position : 3
3 NUT, 5/16-24 Hex, GR5 only 1 shown
Position : 3
1 HANDLE, Lower RH (Adjustable) used on All
Position : 4
1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage GR5
Position : 4
2 GRIP, Height Latch
Position : 4
1 NUT, 1/4-20 Hex
Position : 4
1 PULLEY, Idler
Position : 4
2 WASHER, Spring
Position : 4
2 BUSHING, Axle
Position : 4
1 HINGE, Chute Cover
Position : 4
1 WIRE, Bag Adapter
Position : 4
1 DECAL, Ninja
Position : 4
1 SUPPORT, Wheel
Position : 4
3 WASHER, 5/16” Split Lock only 1 shown
Position : 4
1 BAIL, OPC Control used on All
Position : 5
3 SCREW, 3/8-16 x 1” Hex Washer Self-Tap
Position : 5
6 NUT, 5/16-18 Hex Flange Lock GR5
Position : 5
1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap GR5
Position : 5
1 ASSY, Right Housing (Phantom) (Includes items 6, 7, 8, 9, 10 &
Position : 5
6 WASHER, 7/16” Flat Qty. of (2) for Push; Qty. of (1)
Position : 5
4 WASHER, 7/16” Flat
Position : 5
5 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5
Position : 5
1 ADAPTER, Bag
Position : 5
1 DECAL, SNAPPER
Position : 5
1 TRAY, Tine
Position : 5
3 SPRING only 1 shown
Position : 5
1 CLIP, Zone Control used on All
Position : 6
1 SCREW, 3/8-24 x 2” Hex Head Cap, GR5
Position : 6
2 RETAINER, 5/16” Bolt (Black)
Position : 6
1 ASSEMBLY, Wheel Arm, Right Rear (Round hole) used on Push models (Incl.
Position : 6
1 NUT, 1/4-28 Hex Top Lock
Position : 6
1 HOUSING, Right Side
Position : 6
5 WASHER, 1/4” Internal Tooth Lock
Position : 6
1 ASSEMBLY, Grass Bag Adapter (Includes items 7 thru 14)
Position : 6
1 DECAL, Warning (Deck)
Position : 6
6 KIT, Tine Thatching Spring
Position : 6
1 CABLE, Blade Control (46.75/5.38 length) used on All
Position : 7
2 WASHER, Cone
Position : 7
2 NUT, 5/16-18 Hex Flange Lock GR5
Position : 7
1 ASSEMBLY, Wheel Arm, Left Rear (Square hole) used on Push models (Incl.
Position : 7
2 BUSHING, 3/8” Plastic
Position : 7
3 SCREW, 5/16-24 x 1-1/8” Rib Neck, GR5
Position : 7
5 NUT, 1/4-20 Hex
Position : 7
1 ADAPTER, Bag
Position : 7
1 DECAL, Danger, Cut Finger
Position : 7
1 BUSHING, Wheel Adjuster
Position : 7
1 HANDLE, Wheel Drive used on Self Propelled
Position : 8
1 BLADE, 21” Ninja
Position : 8
1 WELDMENT, Front Wheel Bracket
Position : 8
1 ASSEMBLY, Wheel Arm, Right Rear used on Self-Propelled models
Position : 8
1 SHAFT, Hex Drive
Position : 8
1 SEAL, 5/8” Internal Diameter
Position : 8
1 STOP, Cover
Position : 8
1 BRACKET, Rope Pulley
Position : 8
1 DECAL, Warning (Euro)
Position : 8
1 AXLE, Wheel
Position : 8
1 GRIP,Wheel Drive Handle (International Symbol) used on Self Propelled
Position : 9
1 HUB, Blade Drive 25mm
Position : 9
1 AXLE, 21” qty. 2 on Push models
Position : 9
1 ASSEMBLY, Wheel Arm, Left Rear used on Self-Propelled models
Position : 9
1 PULLEY, Poly-V, 2” O.D. Non-Commercial Models
Position : 9
1 BEARING, Tapered- (Differential Housing)
Position : 9
1 MOLDING, Trim
Position : 9
1 SCREW, 5/16-18 x 1-1/4” Pan Head Machine
Position : 9
1 DECAL, 2004 Year of Mfg.
Position : 9
1 WHEEL, 7.00 x 1.50 Gage
Position : 9
1 CABLE, Clutch Pull (Z-bend, 41.25” long) used on Self Propelled
Position : 10
1 KEY, Hi-Pro #HP506 (Briggs engine)
Position : 10
1 WHEEL ARM, R.H. Rear used on Push models
Position : 10
1 WASHER, 3/8” Flat
Position : 10
1 BALL BEARING, 7/16 I.D., 1/1/8” O.D.
Position : 10
1 BUSHING, Flange
Position : 10
1 DECAL,Euro Community (CE)
Position : 10
10 NUT, 1/4-20 Hex Top Lock only 9 shown
Position : 10
1 COVER, Vinyl used on Self Propelled
Position : 11
1 SCREW, 5/16-18 x 5/16” Hex Socket Head
Position : 11
1 WHEEL ARM, L.H. Rear used on Push models
Position : 11
1 SPRING, Idler, Torsion
Position : 11
1 PLUG, Transmission
Position : 11
1 SPACER, .316 I.D. x .375 O.D. x .310 thick
Position : 11
1 PULLEY, Plastic
Position : 11
1 DECAL, Spart Plug International Symbol
Position : 11
4 WASHER, 1/4” Flat
Position : 11
1 SPRING, Clutch used on Self Propelled
Position : 12
1 PULLEY, Engine Drive (25mm x 2-1/8” O.D.)
Position : 12
1 ARM, Wheel, Right Rear used on Self-Propelled models
Position : 12
1 STUD, Idler (3/8-24 thread)
Position : 12
1 GEAR, Input
Position : 12
1 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 12
1 NUT, 5/16-18 Hex Flange Lock GR5
Position : 12
1 DECAL, Caution, Symbols
Position : 12
2 SPRING, Compression
Position : 12
1 SECTOR, Speed '77VP used on Self Propelled
Position : 13
1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock
Position : 13
1 ARM, Wheel, Left Rear used on Self-Propelled models
Position : 13
1 HOLDER, Half
Position : 13
1 ASSEMBLY, Short Axle
Position : 13
1 RETAINER, 5/16” Bolt
Position : 13
2 WASHER, 15/32” Flat
Position : 13
1 DECAL, OPEI Walk/Ride
Position : 13
2 BOLT, 1/4-20 x 1-1/4” Hex, GR5
Position : 13
2 WIRE TIE, 1.29” Long (Black) used on All
Position : 14
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5
Position : 14
2 BOLT, 5/16-18 x 1” Shoulder
Position : 14
1 BALL BEARING, .38 I.D. Spherical O.D.
Position : 14
1 GEAR, Differential (46 tooth)
Position : 14
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5
Position : 14
4 RIVET
Position : 14
1 DECAL, Noise (European)
Position : 14
2 NUT, 1/4-20 Hex, GR5
Position : 14
1 SPRING, Speed Control used on Self Propelled
Position : 15
1 RETAINER, 5/16” Bolt
Position : 15
2 RETAINER, 5/16” Bolt
Position : 15
1 O-RING
Position : 15
2 PLATE, 46T Gear
Position : 15
1 CHUTE, Side
Position : 15
1 DECAL, Warning
Position : 15
2 CAP, Vinyl
Position : 15
1 WASHER, 3/8” Flat used on Self Propelled
Position : 16
2 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 16
1 NUT, 3/8-24 Hex Center Lock GR5 or B
Position : 16
2 WASHER, Thrust, 3/4” I.D.
Position : 16
2 WASHER, 5/16” Flat
Position : 16
2 DECAL, Deck/Chute International Warning
Position : 16
2 BOLT, 1/4-20 x 2-1/2” Square Neck Carriage only 1 shown
Position : 16
1 GRIP, Speed Control Handle used on Self Propelled
Position : 17
6 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position : 17
1 BRACKET, Right Rear Wheel
Position : 17
1 HOLDER, Half
Position : 17
4 SCREW, #10-32 x 1-1/2” Hex Head Cap GR5 only 1 shown
Position : 17
2 WING-NUT, 5/16-18 Nyloc
Position : 17
1 DECAL, OPC Bail (International Symbol)
Position : 17
6 BOLT, 5/16-18 x 1” Square Neck Carriage, GR5 only 1 shown
Position : 17
1 ANCHOR, Lever used on Self Propelled
Position : 18
1 WASHER, 7/16” Flat
Position : 18
1 BRACKET, Left Rear Wheel
Position : 18
1 CLIP, Transfer Rod 1/4” also shown on HANDLES AND
Position : 18
1 GASKET, Housing
Position : 18
1 COVER, 21” Deck
Position : 18
1 DECAL, Operator Safety
Position : 18
2 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR5
Position : 18
1 GUIDE, Lower V-Belt used on Self Propelled
Position : 19
1 DECAL, Caution, International Symbols used on Euro models
Position : 19
1 AXLE, 21” Rear axle on Push Models;
Position : 19
1 ROD, Transfer also shown on HANDLES AND
Position : 19
3 WASHER, 5/16” Internal/External Tooth Lock only 1 shown
Position : 19
1 DECAL, Patent Numbers not shown
Position : 19
6 WASHER, Reinforcing only 1 shown
Position : 19
2 HOLE PLUG, Polyethylene
Position : 20
1 GUARD, Rear Foot used on Push models
Position : 20
1 BELT, Engine Drive 3L (Stretch)
Position : 20
1 BRACKET, Differential
Position : 20
6 WASHER, 5/16” Split Lock only 1 shown
Position : 20
1 CLIP, Transfer Rod 1/4” used on Self Propelled
Position : 21
1 COVER, Belt used on MRP216518B &
Position : 21
1 GUARD, Rear Foot used on Self-Propelled models
Position : 21
1 THRUST PLATE, Short
Position : 21
4 SCREW, 1/4-20 x 1” Hex Washer Self-Tap only 1 shown
Position : 21
6 NUT, 5/16-18 Hex, GR5 only 1 shown
Position : 21
1 T-NUT, 5/16-18 used on Self Propelled
Position : 22
3 SPACER, .06 Blade Hub
Position : 22
1 RING, Split (Black) used on Self-Propelled models
Position : 22
2 RING, 5/8” External Retaining used on Self-Propelled models
Position : 22
1 SPACER, Axle Gear
Position : 22
2 NUT, 1/2” Push
Position : 22
1 BUSHING, Differential used on Self Propelled
Position : 23
1 FENDER WELDMENT used on Euro models
Position : 23
1 SUPPORT, Foot Guard used on Self-Propelled models
Position : 23
1 BALL BEARING, 3/4” I.D. used on Self-Propelled models
Position : 23
1 ASSEMBLY, Long Axle
Position : 23
4 BEARING, Nyliner
Position : 23
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5 used on All
Position : 24
3 PLUG, 5/16” Square Hole used on Push models; (only one
Position : 24
1 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5 used on Self-Propelled models
Position : 24
1 WASHER, 3/4” Shim
Position : 24
4 GEAR, Pinion (12 tooth)
Position : 24
1 SCREW, 5/16-18 x 1/4” Set
Position : 24
1 SCREW, 5/16-24 x 1” Hex Head Cap GR5 used on All
Position : 25
3 PLUG, 5/16” Round Hole qty. 3 on Push, qty. 2 on Self-
Position : 25
1 WASHER, 1/4” Internal Tooth Lock
Position : 25
1 SHIELD, Hex Shaft
Position : 25
4 SPACER, Pinion Gear
Position : 25
2 WASHER, 1/2” Flat
Position : 25
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 used on All
Position : 26
1 BUSHING, .388 x .625 x 1.62 used on Euro models
Position : 26
1 BALL JOINT, 1/4-28 also shown on HANDLES AND
Position : 26
4 SHAFT, Pinion
Position : 26
1 DECAL, Adjustment
Position : 26
8 NUT, 5/16-18 Hex Flange Lock, GR 5 used on All
Position : 27
2 WASHER, 7/16” Flat used on Euro models
Position : 27
1 NUT, 1/4-28 Hex also shown on HANDLES AND
Position : 27
4 NUT, #10-32 Hex Nyloc
Position : 27
1 DECAL, Thatcherizer
Position : 27
1 NUT, 5/16-24 Hex Center Lock GR5 used on Self Propelled
Position : 28
1 COVER, Belt- IP21S used on Euro models
Position : 28
1 LINK, Transfer also shown on HANDLES AND
Position : 28
1 ASSY, Left Housing (Phantom) (Includes items 8, 9 & 29)
Position : 28
1 CLIP, Cable/Wiring used on All
Position : 29
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5 used on Euro models
Position : 29
1 HOUSING, Left
Position : 29
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2 used on All
Position : 30
3 WASHER, 3/8” Internal Tooth Lock
Position : 30
3 GASKET, 5/8” O. D.
Position : 30
4 KNOB, 5/16-18 Wing (Black) used on All
Position : 31
1 WASHER, 3/8” Flat
Position : 31
3 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5 qty 1 on push model
Position : 32
1 NUT, 3/8-24 Hex
Position : 32
3 WASHER, 1/4” Internal Tooth Lock qty 2 on push
Position : 33
1 NUT, 5/16-18 Hex, GR5
Position : 33
3 NUT, 1/4-20 Hex used on All
Position : 34
1 WASHER, 5/16” Split Lock
Position : 34
1 CABLE-TIE, 7” used on All
Position : 35
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5
Position : 35
4 BUSHING, .27 x .35 x .4 Flange used on Self Propelled
Position : 36
1 CONNECTOR, Transfer Rod
Position : 36
1 PIN, Clutch Handle used on Self Propelled
Position : 37
1 WASHER, .28 x .63 x .06 Flat used on Euro Self-Propelled
Position : 37
1 PUSH-NUT, 1/4” (for handle pin) used on Self Propelled
Position : 38
1 BUSHING
Position : 38
1 DECAL, OPC Bail (International Symbol) used on All; see Decal page
Position : 39
1 SPRING, Wheel Drive
Position : 39
1 GUIDE, Rope (1/4-20 thread) used on All
Position : 40
1 GUIDE, Thrust Plate (3/8-24 thread)
Position : 40
1 FOAM GRIP, 15”, 21 SP used on All
Position : 41
1 RETAINER, 3/8” Bolt
Position : 41
1 DECAL, Speed Sector used on MRP216518B; see
Position : 42
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5
Position : 42
1 DECAL, Speed Sector Int'l Symbol used on EMRP216518B; see
Position : 43
1 DISC, Driven (Cantilever)
Position : 43
1 NUT, 1/4-28 Hex GR5 or B used on All
Position : 44
4 WASHER, 5/16” Internal Tooth Lock used on All
Position : 45
1 CLAMP, 7/8” Double Cable used on Self Propelled
Position : 46
1 SPACER used on Commercial models
Position : 46
1 LEVER, Speed Control used on Self Propelled
Position : 47
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5
Position : 47
1 WASHER, 5/16” Internal Tooth Lock
Position : 48
1 WASHER, .44 x .78 x .025 Curved
Position : 49
1 PIN, 3/32 x 1/2” Cotter
Position : 50
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position : 51
3 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
Position : 52
2 NUT, 5/16-18 Hex Flange Lock, GR
Position : 53
1 SPRING, Clutch
Position : 54
1 WASHER, 1/4” Internal Tooth Lock used on Euro Self-Propelled
Position : 55