Pièces d'usure référencées sur ce modèle
Ces pièces s'usent normalement avec le temps : les remplacer préventivement ou dès les premiers symptômes prolonge la durée de vie de l'appareil.
1 BALL JOINT, 1/4-28 not shown; see Handles & (repère 26) · 2 BALL JOINT, 1/4-28 Self-Propelled Models (repère 39)
Guides utiles
Comment lire une vue éclatée ? Le guide complet pas à pas
Comment trouver la référence exacte d'une pièce détachée
Bien acheter ses pièces détachées : origine, adaptable, occasion
Assistant réparation
Assistant IA
Liste des pièces détachées
1 HANDLE, Upper All
Position : 1
1 DECK, Mower (incl. painted “HV” Deck with Decals) P216018KWV, P216518B,
Position : 1
1 ASSEMBLY, Left Wheel Arm (Consists of items 2, 3, 4, 5B &
Position : 1
1 BEARING, 9/16” I.D. per Rear Wheel Arm
Position : 1
2 WHEEL, 8 x 1.75 Plastic all
Position : 1
2 WHEEL, 10 x 1.75” Plastic Push Models only
Position : 1
1 BELT, Poly-V
Position : 1
4 NUT, 5/16-18 Hex Lock was
Position : 1
1 ASSEMBLY, Bag Adapter & Cover (Euro models only) (Incl items 2 thru 9); used on
Position : 1
1 BATTERY, 12 Volt, 35 CCA
Position : 1
1 DECAL, Easy Walk
Position : 1
1 SCREEN, Fastener Assembly
Position : 1
2 LATCH, Frame Attachment
Position : 1
1 HANDLE, Middle All
Position : 2
10 NUT, 5/16-18 Hex Flange Lock, GR5
Position : 2
1 BOLT, 5/16-18 Hex Washer Face Shoulder per wheel arm assembly
Position : 2
3 SCREW, #10-32 x 3/8” Hex Washer Self-Tap per Rear Wheel Arm
Position : 2
2 NUT, 7/16-20 Hex Center Lock Jam
Position : 2
2 WHEEL, 10 x 1.75” Plastic used on Self-Propelled models
Position : 2
1 LINK, Differential
Position : 2
1 WASHER, Cone
Position : 2
1 ADAPTER, Grass Bag
Position : 2
1 GRASS BAG (Door w/Gray Letters) all
Position : 2
1 HARNESS, Battery
Position : 2
1 DECAL, Throttle Control, KWV
Position : 2
1 RING, Bottom (21.77” Inside Diameter)
Position : 2
1 HANDLE, Lower LH (Adjustable) All
Position : 3
3 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR
Position : 3
1 LATCH, Height per wheel arm assembly
Position : 3
1 LATCH, Height Adjusting (long) per Rear Wheel Arm
Position : 3
2 BUSHING, Axle
Position : 3
2 NUT, 7/16-20 Hex Center Lock Jam all
Position : 3
1 ARM, Clutch Idler
Position : 3
1 PULLEY, Poly-V Belt (3.5 O.D.)
Position : 3
1 COVER, Bag Adapter
Position : 3
1 ASSEMBLY, Bag Wire (12” Wide) all
Position : 3
2 SCREW, #10-24 x 1/2” Pan Head Machine
Position : 3
1 DECAL, Throttle Control, B&S
Position : 3
3 NUT, 5/16-24 Hex, GR5 only 1 shown
Position : 3
2 ROD, Tine
Position : 3
1 HANDLE, Lower RH (Adjustable) All
Position : 4
1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage, GR
Position : 4
1 GRIP, Height Latch per wheel arm assembly
Position : 4
1 NUT, 1/4-20 Hex or
Position : 4
2 WASHER, 7/16” Flat
Position : 4
2 BUSHING, Axle Push Models only
Position : 4
1 PULLEY, Idler
Position : 4
2 WASHER, 44 x .78 x .025 Curved
Position : 4
1 HINGE, Chute Cover
Position : 4
1 CONNECTOR, Grass Bag (weldment) all
Position : 4
2 NUT, #10-24 Square
Position : 4
1 DECAL, Speed Shift
Position : 4
3 WASHER, 5/16” Split Lock only 1 shown
Position : 4
1 SUPPORT, Wheel
Position : 4
1 BAIL, OPC Control All
Position : 5
3 SCREW, 3/8-16 x 1” Self-Tapping engine mount bolts
Position : 5
6 NUT, 5/16-18 Hex Flange Lock, GR
Position : 5
2 PLUG, Wheel all
Position : 5
1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap, GR
Position : 5
1 ASSEMBLY, Right Housing (Incl. items 6, 7, 8, 9, 10 & 30)
Position : 5
5 BOLT, 1/4-20 x 1/2” Short Neck Carriage, GR
Position : 5
1 ADAPTER, Grass Bag used on Euro Self-Propelled
Position : 5
1 DECAL, Chute/Deflector
Position : 5
3 SPRING only 1 shown
Position : 5
1 TRAY, Tine
Position : 5
1 CLIP, Zone Control All
Position : 6
2 PLUG, Hole, Polyethylene
Position : 6
1 RETAINER, 5/16” Bolt
Position : 6
1 ASSEMBLY, Wheel Arm, Right Rear (Round hole) used on Push models (Incl.
Position : 6
1 NUT, 1/4-28 Hex Top Lock
Position : 6
1 HOUSING, Right Side
Position : 6
5 WASHER, 1/4” Internal Tooth Lock
Position : 6
1 ASSEMBLY, Grass Bag Adapter Includes items 7 thru
Position : 6
1 KEY (Set of Two)
Position : 6
1 DECAL, Ignition Switch
Position : 6
6 KIT, Tine Thatching Spring
Position : 6
1 CABLE, Zone Control (52-63/64” Long) 216518B, P216518B,
Position : 7
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR
Position : 7
2 NUT, 5/16-18 Hex Flange Lock, GR
Position : 7
1 ASSEMBLY, Wheel Arm, Left Rear (Square hole) used on Push models (Incl.
Position : 7
4 BUSHING, 3/8” I.D. Nylon
Position : 7
3 SCREW, 5/16-24 x 1-1/8” Rib Neck, GR5
Position : 7
5 NUT, 1/4-20 Hex
Position : 7
1 ADAPTER, Grass Bag used on Domestic Self-
Position : 7
1 BEZEL (Seal & Face Nut)
Position : 7
1 DECAL, Danger, Cut Finger
Position : 7
1 BUSHING, Wheel Adjuster
Position : 7
1 HANDLE, Clutch Self-Propelled Models
Position : 8
1 BOLT, 5/16-18 x 2-1/4”, Hex Flange Lock
Position : 8
1 WELDMENT, Front Wheel Bracket 216518B, P216518B,
Position : 8
1 ASSEMBLY, Wheel Arm, Right Rear used on Self-Propelled models
Position : 8
1 SHAFT, Hex Drive
Position : 8
1 SEAL, 5/8” Internal Diameter
Position : 8
1 STOP, Cover
Position : 8
1 BRACKET, Rope Guide
Position : 8
1 COVER, Switch
Position : 8
1 DECAL, Hi Vac
Position : 8
1 AXLE, Wheel
Position : 8
1 GRIP, International Symbol Self-Propelled Models
Position : 9
1 BUSHING, .388 x .625 x 1.62
Position : 9
1 AXLE, 21”
Position : 9
1 ASSEMBLY, Wheel Arm, Left Rear used on Self-Propelled models
Position : 9
1 PULLEY, Poly-V (2” O.D.) for non-Commercial models
Position : 9
1 BEARING, Tapered- (Differential Housing)
Position : 9
1 MOULDING, Trim
Position : 9
1 SCREW, 5/16-18 x 1-1/4” Pan Head Machine
Position : 9
1 NUT, 5/8-32 Hex Lock
Position : 9
1 DECAL, Ninja
Position : 9
1 WHEEL, 7.00 x 1.50 Gage
Position : 9
1 CABLE, Clutch Control (41-1/4” Long) Self-Propelled Models
Position : 10
1 COVER, Belt European models
Position : 10
1 WHEEL ARM, R.H. Rear (round opening) (right rear) used on Push models
Position : 10
1 WASHER, 3/8” Flat
Position : 10
1 BALL BEARING, 7/16 I.D., 1/1/8” O.D. was
Position : 10
1 BUSHING, Flange, .381 x .625 x .62
Position : 10
1 SWITCH, Ignition (spring loaded ON/OFF 2 prong)
Position : 10
1 DECAL, Snapper
Position : 10
10 NUT, 1/4-20 Hex Top Lock only 9 shown
Position : 10
1 COVER, Vinyl Self-Propelled Models
Position : 11
3 WASHER, 7/16” Flat
Position : 11
1 WHEEL ARM, L.H. Rear (square opening) (left rear) used on Push models
Position : 11
1 SPRING, Idler- Torsion
Position : 11
1 PLUG, Transmission Housing
Position : 11
1 SPACER, .316 I.D. x .375 O.D. x .310 thick
Position : 11
1 PULLEY, Nylon
Position : 11
1 SPACER
Position : 11
1 DECAL, Warning (Deck)
Position : 11
4 WASHER, 1/4” Flat
Position : 11
1 SPRING, Clutch- 21S Self-Propelled Models
Position : 12
1 SCREW, 3/8-24 x 2” Hex Head Cap, GR
Position : 12
1 ARM, Wheel, Right Rear used on Self-Propelled models
Position : 12
1 STUD, Idler (3/8-24 thread)
Position : 12
1 GEAR, Input
Position : 12
1 NUT, 5/16-18 Hex Flange Lock, GR
Position : 12
1 WIRING HARNESS, B&S WBM similar to
Position : 12
1 DECAL, 2004 Year of Mfg.
Position : 12
2 SPRING, Compression
Position : 12
1 BRACKET, Shift All
Position : 13
2 WASHER, Cone
Position : 13
1 ARM, Wheel, Left Rear used on Self-Propelled models
Position : 13
1 HOLDER, Bearing (Inner Half)
Position : 13
1 AXLE, Short
Position : 13
3 WASHER, 15/32” Flat
Position : 13
1 BRACKET, Battery
Position : 13
1 DECAL,Euro Community (CE)
Position : 13
2 BOLT, 1/4-20 x 1-1/4” Hex, GR5
Position : 13
2 TIE, Wire, 1.29 long, black Self-Propelled Models
Position : 14
1 BOLT, 5/16-18 x 1” Shoulder per wheel arm assembly
Position : 14
1 BALL BEARING, Spherical O.D., .38 I.D.
Position : 14
1 GEAR, Differential (46 Tooth)
Position : 14
3 RIVET, 3/16 x .344
Position : 14
1 COVER, Battery
Position : 14
1 DECAL, Spart Plug International Symbol
Position : 14
2 NUT, 1/4-20 Hex, GR5
Position : 14
1 BRACKET, Bell Crank Self-Propelled Models
Position : 15
1 HUB, Blade Drive 25mm I.D.
Position : 15
2 RETAINER, 5/16” Bolt per wheel arm assembly
Position : 15
1 O-RING
Position : 15
2 PLATE, 46T Gear
Position : 15
1 CHUTE, 21” Side P216018KWV
Position : 15
1 PLUG, Chute Adapter P216018KWV, P217018BV,
Position : 15
2 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
Position : 15
1 DECAL, Caution, Symbols
Position : 15
2 CAP, Vinyl
Position : 15
1 SPACER, .33 x .63 x .156 Self-Propelled Models
Position : 16
1 KEY, Woodruff #HP-506 Hi-Pro
Position : 16
1 GRIP, Height Latch per wheel arm assembly
Position : 16
1 NUT, 3/8-24 Hex Center Lock, GR
Position : 16
2 WASHER, Thrust, 3/4” I.D.
Position : 16
2 WASHER, 5/16” Flat
Position : 16
1 BRACE, Bag Adapter P216018KWV & RP216018KWV
Position : 16
3 NUT, 5/16-18 Hex Flange Lock, GR5
Position : 16
1 DECAL, Noise (European)
Position : 16
2 BOLT, 1/4-20 x 2-1/2” Square Neck Carriage only 1 shown
Position : 16
1 BELL CRANK Self-Propelled Models
Position : 17
1 SET SCREW, 5/16-18 x 5/16” Hex Socket
Position : 17
1 BRACKET, Right Rear Wheel all
Position : 17
1 HOLDER, Bearing (Outer Half)
Position : 17
4 SCREW, #10-32 x 1-1/2” Hex Head Cap GR5
Position : 17
2 WING-NUT, 5/16-18 Nyloc
Position : 17
1 SCREW, M6 x 1.0 x 30MM Hex Head Cap P216018KWV & RP216018KWV
Position : 17
1 CLIP, Wiring
Position : 17
2 DECAL, Warning (Euro)
Position : 17
6 BOLT, 5/16-18 x 1” Square Neck Carriage, GR5 only 1 shown
Position : 17
1 CONTROL PANEL (w/o Ground Drive Slot) 216518B
Position : 18
1 PULLEY, Engine (25mm I. D. x 2-1/8” O.D.)
Position : 18
1 BRACKET, Left Rear Wheel all
Position : 18
1 WASHER, .28 x .63 x .06 Flat
Position : 18
1 GASKET, Housing
Position : 18
1 COVER, 21” Deck RP217018BV, RP217018BVE,
Position : 18
1 SLEEVE, .237/.242 I.D. x .3135/.3185 O.D. x .748 not shown; P216018KWV &
Position : 18
1 CHARGER, Battery (120 Volt; 60 Hertz)
Position : 18
1 DECAL, OPEI Walk/Ride
Position : 18
2 BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR5
Position : 18
4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx) All
Position : 19
6 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap EP217018BV & ERP217018BV
Position : 19
1 AXLE, 21” qty. 2 on push models; qty. 1 on
Position : 19
1 COTTER PIN, .06 x .50
Position : 19
3 WASHER, 5/16” Internal/External Tooth Lock
Position : 19
2 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 19
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5
Position : 19
1 DECAL, Warning
Position : 19
6 WASHER, Reinforcing only 1 shown
Position : 19
1 WASHER, .33 x .88 x .09 Flat Self-Propelled Models
Position : 20
1 WELDMENT, Fender European models
Position : 20
1 FOOT GUARD, Long, Rear Push Models only
Position : 20
1 BELT, Engine Drive (Stretch)
Position : 20
1 BRACKET, Differential
Position : 20
2 DECAL, Deck/Chute International Warning
Position : 20
6 WASHER, 5/16” Split Lock only 1 shown
Position : 20
1 SCREW, 5/16-18 x 7/8” Hex Head Cap, GR 5 Self-Propelled Models
Position : 21
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5
Position : 21
1 FOOT GUARD, Rear used on Domestic Self-
Position : 21
1 THRUST PLATE, Short
Position : 21
4 SCREW, 1/4-20 x 1” Hex Washer Self-Tap
Position : 21
1 DECAL, OPC Bail (International Symbol)
Position : 21
6 NUT, 5/16-18 Hex, GR5 only 1 shown
Position : 21
1 TEENUT, 5/16-18 Self-Propelled Models
Position : 22
1 RETAINER, 5/16” Bolt
Position : 22
1 RING, Split (Black) used on Self-Propelled models
Position : 22
2 RETAINING RING, .625 External
Position : 22
1 SPACER, Axle Gear
Position : 22
1 DECAL, Patent Numbers not shown
Position : 22
2 NUT, 1/2” Push
Position : 22
1 BUSHING, Differential, .328 x .625 x .41 Self-Propelled Models
Position : 23
3 NUT, 5/16-18 Hex Flange Lock, GR
Position : 23
1 SUPPORT, Foot Guard used on Self-Propelled models
Position : 23
1 BALL BEARING- 3/4” Bore
Position : 23
1 ASSEMBLY, Long Axle
Position : 23
4 BEARING, Nyliner
Position : 23
3 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5 All
Position : 24
2 AIR LIFT
Position : 24
1 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5 used on Self-Propelled models
Position : 24
1 GUIDE, Thrust Plate (3/8-24 thread)
Position : 24
4 GEAR, Pinion (12 tooth)
Position : 24
1 SCREW, 5/16-18 x 1/4” Set
Position : 24
2 NUT, 5/16-18 Hex Flange Lock, GR5 All
Position : 25
4 WASHER, 5/16” Internal Tooth Lock
Position : 25
1 WASHER, 1/4” Internal Tooth Lock
Position : 25
1 SHIELD, Hex Shaft European models only
Position : 25
4 SPACER, Pinion Gear
Position : 25
2 WASHER, 1/2” Flat
Position : 25
1 NUT, 5/16-18 Hex Center Lock Self-Propelled Models
Position : 26
4 NUT, 5/16-24 Hex, GR
Position : 26
2 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR
Position : 26
1 BALL JOINT, 1/4-28 not shown; see Handles &
Position : 26
4 SHAFT, Pinion
Position : 26
1 DECAL, Adjustment
Position : 26
1 LEVER, Shift Self-Propelled Models
Position : 27
4 SCREW, 5/16-24 x 21/32” Machine
Position : 27
2 NUT, 1/4-28 Hex not shown; see Handles &
Position : 27
4 NUT, #10-32 Hex Nyloc
Position : 27
1 DECAL, Thatcherizer
Position : 27
1 NUT, 5/16-24 Hex Center Lock GR5 All
Position : 28
3 SPACER, .06 Thick for blade hub
Position : 28
1 LINK, Transfer (1/4-28 thread)
Position : 28
1 ASSY, Left Housing (Phantom)
Position : 28
1 CLIP, Wiring Harness All
Position : 29
1 COVER, Belt
Position : 29
1 WASHER, 3/4” Shim
Position : 29
1 HOUSING, Left
Position : 29
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2 All
Position : 30
3 PLUG, 5/16” Square Hole Push Models
Position : 30
3 WASHER, 3/8” Internal Tooth Lock
Position : 30
3 GASKET, 5/8” O. D.
Position : 30
4 KNOB, 5/16-18 Wing (Black) All
Position : 31
2 PLUG, 5/16” Round Hole qty. 3 on Push Models
Position : 31
1 WASHER, 3/8” Flat
Position : 31
2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5 All
Position : 32
1 DECAL, Caution, International Symbols European models
Position : 32
2 NUT, 3/8-24 Hex
Position : 32
3 WASHER, 1/4” Internal Tooth Lock All
Position : 33
1 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 33
1 SPRING, Clutch- 21S
Position : 33
3 NUT, 1/4-20 Hex All
Position : 34
1 SCREW, 1/4-20 x 2” Hex Head Cap, GR
Position : 35
1 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR
Position : 35
2 BUSHING, .27 x .35 x .4 Flange Self-Propelled Models
Position : 36
2 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap
Position : 36
1 PIN, 1/4 x 1-1/2” Self-Propelled Models
Position : 37
1 COTTER PIN, 3/32 x 1/2”
Position : 37
1 PUSH-NUT, 1/4” Self-Propelled Models
Position : 38
1 BUSHING, Powdered Metal
Position : 38
2 BALL JOINT, 1/4-28 Self-Propelled Models
Position : 39
1 DISC, Driven (Cantilever)
Position : 39
4 NUT, 1/4-28 Hex Self-Propelled Models
Position : 40
1 WASHER, 44 x .78 x .025 Curved
Position : 40
1 FOAM GRIP, 15” long All
Position : 41
1 RETAINER, 3/8” Bolt
Position : 41
1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5 Self-Propelled Models
Position : 42
1 SPRING, Wheel Drive
Position : 42
1 NUT, 3/8-16 Hex Center Lock All
Position : 43
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5
Position : 43
4 WASHER, 5/16” Internal Tooth Lock All
Position : 44
8 WASHER, 7/16” Flat Self-Propelled Models
Position : 45
2 BUSHING, Flange, .381 x .625 x .62
Position : 45
2 WASHER, Nylon Self-Propelled Models
Position : 46
1 SPACER, .500 x .65 x 1.75
Position : 46
1 ROD, Speed Control (1/4-28 thread) Self-Propelled Models
Position : 47
1 GUIDE, Rope (1/4-20 thread) All
Position : 48
1 WASHER, 5/16” Internal Tooth Lock
Position : 48
1 NUT, 1/4-28 Hex GR5 or B All
Position : 49
2 CABLE-TIE, 7” Self-Propelled Models
Position : 50
1 THROTTLE CONTROL, .48 x .61 Briggs models; see also Throttle
Position : 51
1 THROTTLE KNOB All
Position : 52
1 KNOB, Shift Self-Propelled Models
Position : 53
1 CLAMP, 7/8” Double Cable Self-Propelled Models
Position : 54
1 SCREW, #8-32 x 1/2” Cross Recess Filister Head Machine Self-Propelled Models
Position : 55
1 NUT, #8-32 Hex Self-Propelled Models
Position : 56
1 BELT GUIDE, Lower Self-Propelled Models
Position : 57
1 WASHER, Belleville Self-Propelled Models
Position : 58
4 WASHER, 1/4” Internal Tooth Lock Self-Propelled Models
Position : 59
1 WASHER, 3/8” Flat Self-Propelled Models
Position : 60
1 COTTER PIN, 5/16 Self Lock Self-Propelled Models
Position : 61
1 DECAL, Easy Walk All
Position : 62
1 CLAMP, Casing models with Briggs Engine
Position : 63
1 SCREW,#10-32 x 5/8” Self-Tap models with Briggs Engine
Position : 64
1 SCREW, 5/16-24 x 1” Hex Head Cap GR5 All
Position : 65