Vue éclatée Fischer wmrp216517b
Découvrez la vue éclatée complète Fischer wmrp216517b, un guide indispensable pour identifier facilement toutes les pièces détachées de votre appareil. Que vous soyez à la recherche d'une pièce en particulier ou simplement pour vous aider à la réparation, notre présentation détaillée vous aide à comprendre chaque composant de. Optimisez la maintenance et la réparation de votre appareil grâce à des schémas précis et des références adaptées. Trouvez rapidement les pièces qu'il vous faut pour prolonger la durée de vie de votre Fischer wmrp216517b et éviter les pannes imprévues.
Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
1 HANDLE, Upper Was 72931 (used on All)
Position : 1
1 HANDLE, Upper used on Push Models (except
Position : 1
1 HANDLE, Upper used on Push Model
Position : 1
1 HANDLE, Upper used on Self-Propelled
Position : 1
1 DECK, 21” Mower Includes painted deck with
Position : 1
1 ASSEMBLY, Right Wheel Arm (Consists of items 2, 3, 4, 5A &
Position : 1
2 BALL BEARING, 9/16” I.D.
Position : 1
2 BALL BEARING, 9/16” I.D. (Commercial) Was
Position : 1
1 BELT, Poly-Vee
Position : 1
1 NUT, 5/16-24 Hex Lock, GR C Was
Position : 1
2 WHEEL, 8 x 1.75 Plastic used on 2002 Model Year and
Position : 1
1 DECAL, Blade Control
Position : 1
ASSEMBLY, Bag Adapter & Cover Includes items 2 thru 9; used on
Position : 1
1 GRASS BAG, Slider Type (Black)
Position : 1
2 ** LATCH, Frame Attachment
Position : 1
1 SCREEN, Fastener Assembly
Position : 1
1 HANDLE, Middle- 1990 used on All
Position : 2
1 HANDLE, Middle-
Position : 2
10 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position : 2
2 BOLT, 5/16-18 Hex Washer Face Shoulder
Position : 2
3 SCREW, #10-32 x 3/8” Hex Washer Self-Tap (Torx)
Position : 2
1 LINK, Differential
Position : 2
1 WASHER, Cone
Position : 2
2 WHEEL, 8 x 1.75 Plastic used on 2003 Model Year and
Position : 2
1 DECAL, Blade Control (Euro)
Position : 2
1 ADAPTER, Grass Bag
Position : 2
1 ASSEMBLY, Slider
Position : 2
1 RING, Bottom
Position : 2
1 PLUG, Chute Adapter
Position : 2
1 HANDLE, Lower Left Hand used on All
Position : 3
1 HANDLE, Lower Left Hand
Position : 3
9 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5 Was
Position : 3
2 LATCH, Height
Position : 3
2 LATCH, Height Adjusting (Long)
Position : 3
1 ARM, Clutch Idler
Position : 3
1 PULLEY, Poly-Vee Belt
Position : 3
2 NUT, 7/16-20 Hex Center Lock Jam
Position : 3
1 DECAL, Speed Select used on Self-Propelled models
Position : 3
1 COVER, Bag Adapter
Position : 3
1 CONNECTOR, Grass Bag (weldment)
Position : 3
2 ROD, Tine
Position : 3
3 NUT, 5/16-24 Hex, GR5 Was 90223, only 1 shown
Position : 3
1 BLADE, 21” Quad Edge Ninja
Position : 3
1 HANDLE, Lower Right Hand used on All
Position : 4
1 HANDLE, Lower Right Hand
Position : 4
1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage GR5
Position : 4
2 GRIP, Latch
Position : 4
1 NUT, 1/4-20 Hex Was
Position : 4
2 PULLEY, Idler
Position : 4
2 WASHER, Spring only 1 shown
Position : 4
2 BUSHING, Axle
Position : 4
1 DECAL, Speed Select (Euro) used on Self-Propelled models
Position : 4
1 HINGE, Chute Cover
Position : 4
1 WIRE, Bag Adapter
Position : 4
1 SUPPORT, Wheel
Position : 4
3 WASHER, 5/16” Split Lock only 1 shown
Position : 4
1 BAIL, Blade Control used on All
Position : 5
1 BAIL, OPC Control (12.5" Wide)
Position : 5
3 SCREW, 3/8-16 x 1” Self-Tap (engine mounting screws)
Position : 5
6 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position : 5
1 SCREW, 1/4-28 x 1-3/8” Hex Head Cap GR5
Position : 5
1 ASSEMBLY, Right Housing (Includes items 6, 7, 8, 9, 10 &
Position : 5
6 WASHER, 7/16 x 1” O.D. Flat Qty. of (2) for Push; Qty. of (1)
Position : 5
4 WASHER, 7/16 x 1” O.D. Flat
Position : 5
1 DECAL, Danger, Cut Finger
Position : 5
5 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5
Position : 5
1 ADAPTER, Bag
Position : 5
1 TRAY, Tine
Position : 5
3 SPRING only 1 shown
Position : 5
1 CLIP, Blade Control used on All
Position : 6
1 CLIP, Blade Control
Position : 6
1 SCREW, 3/8-24 x 1-3/4 Hex Head Cap GR5
Position : 6
2 RETAINER, 5/16” Bolt (Black)
Position : 6
1 ASSEMBLY, Wheel Arm, Right Rear (Round hole) used on Push models (Incl.
Position : 6
1 NUT, 1/4-28 Hex Top Lock
Position : 6
1 HOUSING, Right Side
Position : 6
2 PLUG, Wheel
Position : 6
1 DECAL, Warning (Euro)
Position : 6
5 WASHER, 1/4” Internal Tooth Lock Was
Position : 6
1 ASSEMBLY, Grass Bag Adapter (Includes items 7 thru 14)
Position : 6
6 KIT, Tine Thatching Spring Was
Position : 6
1 CABLE, Blade Control (49-1/4” long) used on All
Position : 7
1 CABLE, Blade Control (49-1/4” long) used on MR216517B &
Position : 7
1 CABLE, Blade Control (46.-15/16” long) used on All Other Models
Position : 7
2 WASHER, 3/8” I.D. Cone
Position : 7
2 NUT, 5/16-18 Hex Flange Lock Was
Position : 7
1 ASSEMBLY, Wheel Arm, Left Rear (Square hole) used on Push models (Incl.
Position : 7
2 BUSHING, 3/8” Plastic
Position : 7
3 SCREW, 5/16-24 x 1-1/8” Rib Neck, GR5
Position : 7
1 DECAL, Shift Warning used on Self-Propelled models
Position : 7
5 NUT, 1/4-20 Hex Was
Position : 7
1 ADAPTER, Bag
Position : 7
1 ** BUSHING, Wheel Adjuster
Position : 7
1 HANDLE, Wheel Drive used on Self-Propelled
Position : 8
1 HANDLE, Wheel Drive used on Self-Propelled
Position : 8
1 WELDMENT, Front Wheel Bracket Was
Position : 8
1 ASSEMBLY, Wheel Arm (Right Rear) Was 54230 (Self-Propelled
Position : 8
1 ASSEMBLY, Wheel Arm, Right Rear Was 54224 (Commercial
Position : 8
1 SHAFT, Hex Drive
Position : 8
2 SEAL, 5/8” Internal Dia.
Position : 8
1 DECAL, SNAPPER, 3.87 Dia. (Push)
Position : 8
1 STOP, Cover
Position : 8
1 BRACKET, Rope Pulley
Position : 8
1 ** AXLE, Wheel
Position : 8
1 GRIP, Wheel Drive Handle used on Self-Propelled
Position : 9
1 GRIP, Wheel Drive Handle used on Self-Propelled
Position : 9
1 HUB, Blade Drive 25mm
Position : 9
1 AXLE
Position : 9
1 ASSEMBLY, Wheel Arm (Left Rear) Was 54231 (Self-Propelled
Position : 9
1 ASSEMBLY, Wheel Arm, Left Rear Was 54225 (Commercial
Position : 9
1 PULLEY, Poly-V, 2” O.D. Non Commercial Models
Position : 9
2 BEARING, Tapered- (Differential Housing)
Position : 9
1 DECAL, Warning
Position : 9
1 MOLDING, Trim
Position : 9
1 SCREW, 5/16-18 x 1-1/4” Pan Head Machine
Position : 9
1 WHEEL, 7.00 x 1.50 Gage
Position : 9
1 CABLE, Clutch Pull (Z-Bend, 38-5/8” long) used on Self-Propelled
Position : 10
1 CABLE, Clutch Pull (Z-Bend, 38-5/8” long) used on Self-Propelled
Position : 10
1 KEY, Hi-Pro #HP506 (Briggs engine)
Position : 10
1 ARM, Round Axle End, Right Rear (Round hole) used on Push models
Position : 10
1 WASHER, 3/8” Flat
Position : 10
1 BEARING, Ball, .437 I.D. x 1.125 O.D. x .375 Thk. Was
Position : 10
1 DECAL, Operator Safety
Position : 10
1 BUSHING, Flange
Position : 10
10 * NUT, 1/4-20 Hex Top Lock Was 90761, only 9 shown
Position : 10
1 COVER, Vinyl used on Self-Propelled
Position : 11
1 COVER, Vinyl used on Self-Propelled
Position : 11
1 SCREW, 5/16-18 x 5/16” Hex Socket Set
Position : 11
1 ARM, Square Axle End, Left Rear (Square hole) used on Push models
Position : 11
1 SPRING, Torsion
Position : 11
1 PLUG, Housing
Position : 11
1 DECAL, Caution Symbols
Position : 11
1 SPACER, .316 I.D. x .375 O.D. x .310 thick
Position : 11
1 PULLEY, Plastic
Position : 11
4 * WASHER, 1/4” Flat Was
Position : 11
1 SPRING, Clutch used on Self-Propelled
Position : 12
1 SPRING, Clutch used on Self-Propelled
Position : 12
1 PULLEY, Engine Drive (25mm x 2-1/8” O.D.)
Position : 12
1 ARM, Wheel, Right Rear used on Self-Propelled models
Position : 12
1 STUD, Idler (3/8-24 thread)
Position : 12
1 GEAR, Input
Position : 12
1 DECAL, SNAPPER (Deck) silver letters, black background
Position : 12
1 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 12
1 NUT, 5/16-18 Hex Flange Lock GR5 Was
Position : 12
2 ** SPRING, Compression
Position : 12
1 SECTOR, Speed used on Self-Propelled
Position : 13
1 BOLT, 5/16-18 x 2-1/4” Hex Flange Lock used on Euro models
Position : 13
1 ARM, Wheel, Left Rear used on Self-Propelled models
Position : 13
1 HOLDER, Bearing (Inner Half)
Position : 13
1 AXLE, Short
Position : 13
1 DECAL, SNAPPER silver letters, black background
Position : 13
1 RETAINER, 5/16” Bolt
Position : 13
2 WASHER, 15/32” Flat
Position : 13
2 * BOLT, 1/4-20 x 1-1/4” Hex, GR
Position : 13
1 BOLT, 5/16-18 x 1” Square Neck Carriage GR 5 Was 91238 (used on All)
Position : 14
1 WIRE TIE, 1.29” Long (Black)
Position : 14
2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 Was 90001 (only one shown)
Position : 14
2 BOLT, 5/16-18 x 1” Shoulder
Position : 14
1 BEARING, Ball, .38 I.D. Spherical O.D.
Position : 14
1 GEAR, Differential (46 tooth)
Position : 14
1 DECAL, Euro Community (CE)
Position : 14
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 Was
Position : 14
4 RIVET, 3/16 x .344
Position : 14
2 * NUT, 1/4-20 Hex, GR 5 Was
Position : 14
1 SPRING, Speed Control used on Self-Propelled
Position : 15
1 SPRING, Speed Control used on Self-Propelled
Position : 15
2 RETAINER, 5/16” Bolt (only one shown)
Position : 15
2 RETAINER, 5/16” Bolt
Position : 15
1 O-RING
Position : 15
2 PLATE, 46T Gear
Position : 15
1 DECAL, SNAPPER (Commercial) gold letters/red border/black
Position : 15
1 CHUTE, Side
Position : 15
2 ** CAP, Vinyl
Position : 15
1 WASHER, 3/8” Flat used on Self-Propelled
Position : 16
1 WASHER, 3/8” Flat used on Self-Propelled
Position : 16
3 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position : 16
1 NUT, 3/8-24 Hex Center Lock GR5 or B
Position : 16
2 WASHER, Thrust, 3/4” I.D.
Position : 16
1 DECAL, Spark Plug International Symbol
Position : 16
2 WASHER, 3/8" Flat Was
Position : 16
2 * BOLT, 1/4-20 x 2-1/2” Square Neck Carriage only 1 shown
Position : 16
1 GRIP, Speed Control Handle Was 29383, used on Self-
Position : 17
4 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 90539 (used on Euro
Position : 17
1 BRACKET, Right Rear Wheel
Position : 17
1 HOLDER, Bearing (Outer Half)
Position : 17
4 SCREW, #10-32 x 1-1/2” Hex Head Cap GR5 only 1 shown
Position : 17
1 DECAL, Deck Warning
Position : 17
2 WING-NUT, 5/16-18 Nyloc
Position : 17
6 * BOLT, 5/16-18 x 1” Square Neck Carriage, GR 5 Was 90383, only 1 shown
Position : 17
1 DECAL, Speed Select used on Self-Propelled
Position : 18
1 WASHER, 7/16” Flat
Position : 18
1 BRACKET, Left Rear Wheel
Position : 18
1 CLIP, Transfer Rod 1/4”
Position : 18
1 GASKET, Housing
Position : 18
1 DECAL, Ninja
Position : 18
1 COVER, 21” Deck
Position : 18
2 * BOLT, 1/4-20 x 3/4” Square Neck Carriage, GR 5 Was
Position : 18
1 GUIDE, Lower V-Belt used on Self-Propelled
Position : 19
1 GUIDE, Lower V-Belt used on Self-Propelled
Position : 19
1 DECAL, Operator Safety used on Euro models
Position : 19
1 AXLE Rear axle on Push Models;
Position : 19
1 ROD, Transfer used on Non-Euro models
Position : 19
3 WASHER, 5/16” Internal/External Tooth Lock only 1 shown
Position : 19
1 DECAL, Patent Numbers
Position : 19
2 NUT, 5/16-18 Hex Large Flange Center Lock
Position : 19
6 * WASHER, Reinforcing (.343 I.D.) only 1 shown
Position : 19
1 ROD, Transfer used on Self-Propelled
Position : 20
1 ROD, Transfer used on Self-Propelled
Position : 20
2 PLUG, Hole Polyethylene
Position : 20
1 GUARD, Rear Foot used on Push models
Position : 20
1 BELT, Engine Drive 3L (Stretch) used on Self-Propelled
Position : 20
1 BRACKET, Differential
Position : 20
1 DECAL, Primer (European)
Position : 20
6 * WASHER, 5/16” Split Lock only 1 shown
Position : 20
1 CLIP, Transfer Rod 1/4” used on Self-Propelled
Position : 21
1 CLIP, Transfer Rod 1/4” used on Self-Propelled
Position : 21
1 GUARD, Rear Foot used on Self-Propelled models
Position : 21
1 GUARD, Rear Foot used on Euro Self-Propelled
Position : 21
1 PLATE, Thrust
Position : 21
4 SCREW, 1/4-20 x 1-1/4” Hex Washer Self-Tap only 1 shown
Position : 21
1 DECAL, Air Filter (European)
Position : 21
6 * NUT, 5/16-18 Hex, GR 5 Was 90196, only 1 shown
Position : 21
1 TEE-NUT, 5/16-18 used on Self-Propelled
Position : 22
1 TEE-NUT, 5/16-18 used on Self-Propelled
Position : 22
1 SPACER, Blade Hub
Position : 22
1 RING, Split (Black) used on Self-Propelled models
Position : 22
2 RING, 5/8” External Retaining used on Self-Propelled
Position : 22
1 SPACER, Axle Gear
Position : 22
1 DECAL, Deck/Chute (European)
Position : 22
2 ** NUT, 1/2” Push
Position : 22
1 BUSHING, Differential used on Self-Propelled
Position : 23
1 BUSHING, Differential used on Self-Propelled
Position : 23
1 WELDMENT, Fender used on Euro models
Position : 23
1 SUPPORT, Foot Guard used on Self-Propelled models
Position : 23
1 BALL BEARING, 3/4” I.D. used on Self-Propelled
Position : 23
1 AXLE, Long
Position : 23
1 DECAL, 2003 Year of Manufacture shown
Position : 23
4 ** BEARING, Nyliner
Position : 23
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5 used on All
Position : 24
2 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR5
Position : 24
3 PLUG, 5/16” Square Hole used on Push models; (only one
Position : 24
1 BOLT, 1/4-20 x 1/2” Short Neck Carriage GR5 Was 90005 (used on Self-
Position : 24
4 SCREW, #10-32 x 1/4” Self-Tap Machine
Position : 24
4 GEAR, Pinion (12 tooth)
Position : 24
1 DECAL, Chute/Deflector Warning
Position : 24
1 ** SET SCREW, 5/16-18 x 1/4” slotted headless cup point
Position : 24
1 SCREW, 5/16-24 x 1” Hex Head Cap GR5 used on All
Position : 25
1 SCREW, 5/16-24 x 1” Hex Head Cap GR5
Position : 25
3 PLUG, 5/16” Round Hole qty. 3 on Push, qty. 2 on Self-
Position : 25
1 WASHER, 1/4” Internal Tooth Lock Was
Position : 25
1 SHIELD, Hex Shaft used on Self-Propelled Euro
Position : 25
4 SPACER, Pinion Gear
Position : 25
1 DECAL, Noise (European)
Position : 25
2 WASHER, 1/2” Flat
Position : 25
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 Was 91026 (used on All)
Position : 26
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5
Position : 26
1 WASHER, 5/16” Flat used on Euro models
Position : 26
BALL JOINT, 1/4-28 used on Self-Propelled Euro
Position : 26
4 SHAFT, Pinion
Position : 26
1 DECAL, OPEI
Position : 26
1 DECAL, Adjustment
Position : 26
10 NUT, 5/16-18 Hex Flange Lock GR5 Was 91070 (used on All)
Position : 27
10 NUT, 5/16-18 Hex Flange Lock GR5
Position : 27
2 WASHER, 7/16” Flat used on Euro models
Position : 27
1 NUT, 1/4-28 Hex GR5 used on Self-Propelled Euro
Position : 27
4 NUT, #10-32 Hex Nyloc only 1 shown
Position : 27
1 DECAL, Caution Tag not used in 2003 model year
Position : 27
1 DECAL, Thatcherizer
Position : 27
1 BRACKET, Speed Control Rod used on Self-Propelled
Position : 28
1 NUT, 5/16-24 Hex Center Lock GR5
Position : 28
1 COVER, Belt used on Euro models
Position : 28
1 LINK, Transfer used on Self-Propelled Euro
Position : 28
1 ASSEMBLY, Left Housing (Includes items 8, 9 & 29)
Position : 28
2 WIRE TIE, 1.29” Long (Black) used on All
Position : 29
1 CLIP, Cable/Wiring
Position : 29
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5 used on Euro models
Position : 29
1 WASHER, 3/4” Shim
Position : 29
1 HOUSING, Left
Position : 29
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2 Was 91189 (used on All)
Position : 30
4 SCREW, 5/16-18 x 1-7/8” Curved Head GR2
Position : 30
1 BUSHING used on Euro models
Position : 30
3 WASHER, 3/8” Internal Tooth Lock
Position : 30
3 GASKET, 5/8” O. D.
Position : 30
4 T-KNOB, 5/16-18 (BLACK) used on All
Position : 31
4 T-KNOB, 5/16-18 (BLACK)
Position : 31
1 WASHER, 3/8” Flat
Position : 31
1 LEVER, Speed Control used on Self-Propelled
Position : 32
2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR5
Position : 32
3 NUT, 3/8-24 Hex, GR B Was
Position : 32
4 WASHER, 5/16” Internal Tooth Lock used on All
Position : 33
3 WASHER, 1/4” Internal Tooth Lock
Position : 33
1 NUT, 5/16-18 Hex GR5 or B Was 90196 (continued on next
Position : 33
1 NUT, 1/4-28 Hex GR5 or B used on All
Position : 34
3 NUT, 1/4-20 Hex GR5 or B
Position : 34
1 WASHER, 5/16” Split Lock
Position : 34
1 FOAM GRIP, .84 I.D. x 11” long Was 73115 (Used on All)
Position : 35
1 SCREW, 1/4-20 x 2” Hex Head Cap GR5 used on All except MR216517
Position : 35
1 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR5 Was
Position : 35
2 BUSHING used on All
Position : 36
2 BUSHING
Position : 36
1 CONNECTOR, Transfer Rod
Position : 36
1 PIN, Clutch Handle used on Self-Propelled
Position : 37
1 PIN, Clutch Handle used on Self-Propelled
Position : 37
1 WASHER, Flat 1/4" (European Models Only) used on Self-Propelled Euro
Position : 37
1 PUSH-NUT, 1/4” (for handle pin) used on Self-Propelled
Position : 38
1 PUSH-NUT, 1/4” (for handle pin) used on Self-Propelled
Position : 38
1 BUSHING
Position : 38
1 DECAL, Blade Control (Right Hand Side) used on all (except Euro)
Position : 39
1 SPRING, Wheel Drive
Position : 39
1 GUIDE, Rope used on All
Position : 40
2 GUIDE, Rope used on All except MR216517
Position : 40
1 GUIDE, Thrust Plate (3/8-24 thread)
Position : 40
1 CLAMP, 7/8” Double Cable used on All
Position : 41
1 FOAM GRIP, .84 I.D. x 11” long
Position : 41
1 RETAINER, 3/8” Bolt
Position : 41
1 NUT, 5/16-24 Hex Center Lock GR5 Was 91074 (used on All)
Position : 42
1 BOLT, 5/16-18 x 5/8” Short Neck Carriage GR5 Was
Position : 42
1 DECAL, Shift Warning used on Self-Propelled
Position : 43
1 CLAMP, Casing used on All except MR216517
Position : 43
1 DISC, Driven (Cantilever)
Position : 43
3 NUT, 1/4-20 Hex Was 91100 (used on All)
Position : 44
4 WASHER, 5/16” Internal Tooth Lock
Position : 44
1 BRACKET, Deck Was 31919 (Now 17696 +
Position : 44
3 WASHER, 1/4” Internal Tooth Lock used on All
Position : 45
1 SCREW, 5/16-24 x 1-1/2” Round Hd. Machine, GR5 used on All except MR216517
Position : 45
2 BUSHING, Flange
Position : 45
1 SCREW, 1/4-20 x 1-3/4” Hex Head Cap GR5 Was 91222 (used on All)
Position : 46
1 CLAMP, 7/8” Double Cable
Position : 46
1 SPACER used on Commercial models
Position : 46
1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR5
Position : 47
1 GUIDE, Rope used on Self-Propelled
Position : 48
1 WASHER, 5/16” Internal Tooth Lock
Position : 48
1 NUT, 1/4-20 Hex GR5 or B used on Self-Propelled
Position : 49
1 WASHER, Spring
Position : 49
1 CABLE-TIE, 7” used on Self-Propelled
Position : 50
1 PIN, 3/32 x 1/2” Cotter Was
Position : 50
1 SCREW, 1/4-20 x 1-1/2” Hex Head Cap, GR5 used on Self-Propelled
Position : 51
2 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was
Position : 51
1 SCREW, #10-32 x 5/8” Hex Head Self-Tap used on All except MR216517
Position : 52
3 BOLT, 5/16-18 x 1/2” Short Neck Carriage GR5
Position : 52
1 WIRE TIE, 11” Long (Black) used on Self-Propelled
Position : 53
2 NUT, 5/16-18 Hex Flange Lock, GR5 Was
Position : 53
1 BOLT, 5/16-18 x 1” Square Neck Carriage GR5 used on MRP216517B
Position : 54
1 SPRING, Clutch
Position : 54
1 WASHER, 1/4” Internal Tooth Lock used on Self-Propelled Euro
Position : 55
KIT, Drive Disc Assembly
Position : 56