Réparer son aspirateur et nettoyage Snapper : les pannes courantes
Les symptômes les plus fréquents sur ce type d'appareil, et les pièces de cette vue éclatée à contrôler en priorité. Avant toute intervention : appareil débranché, photos à chaque étape.
Moteur et alimentation
Des charbons moteur usés font des étincelles et une odeur caractéristique avant la panne franche ; l'enrouleur de câble et son contact tournant sont l'autre classique.
Sur cette vue : 1 CLUTCH CABLE, Auger Drive- RH parts number is stamped on (repère 4) · 1 CLUTCH CABLE, Ground Drive- LH parts number is stamped on (repère 49).
Guides utiles
Comment lire une vue éclatée ? Le guide complet pas à pas
Comment trouver la référence exacte d'une pièce détachée
Bien acheter ses pièces détachées : origine, adaptable, occasion
Assistant réparation
Assistant IA
Liste des pièces détachées
2 NUT, 5/16-18 Hex Nyloc
Position : 1
1 PUSH NUT, Pal. .375 Dia. Stud Cap
Position : 1
1 END PLATE, RH- Auger Housing- Red
Position : 1
1 CHUTE, Discharge A Chute/Deflector Assembly
Position : 1
1 PULLEY, Auger Input
Position : 1
3 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap or
Position : 1
4 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR 5 or
Position : 1
4 SCREW, 5/16-24 x 1-1/4” Hex Head Cap, GR
Position : 1
2 KLIK- PIN, .310 ID x 1-3/4” Long
Position : 1
1 DECAL, Dashboard- RH used on Domestic Models
Position : 1
1 DECAL, Dashboard- RH- Euro
Position : 1
1 STRAP, Ground (not shown) B&S #
Position : 1
1 BRACKET, Snow Stick- Lower
Position : 2
1 KNOB, Spinner
Position : 2
1 WELDMENT, Auger Housing - 22” - Red
Position : 2
1 WELDMENT, Auger Housing - 24” - Red
Position : 2
1 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR
Position : 2
2 SET SCREW, 5/16-18 x 1/2” Square Head Cup Point or
Position : 2
1 BRACKET, Bushing
Position : 2
1 WASHER, 5/16” Flat
Position : 2
1 VALVE STEM AND CAP per tire assembly
Position : 2
1 DECAL, Shift Pattern
Position : 2
1 CLAMP, Regulator (not shown) B&S #
Position : 2
4 SCREW, 5/16-18 x 3/4” Hex Head Cap or
Position : 3
3 BUSHING, .376 x .437 x .20
Position : 3
3 RETAINER NUT, 5/16-18
Position : 3
1 DEFLECTOR, Chute
Position : 3
2 KEY, 3/16 x 3/4” Woodruff or
Position : 3
1 NUT, 3/8-16 Hex, GR 5 or B
Position : 3
1 WIRE, Belt Stop replaced by 7100117 &
Position : 3
1 TUBE, Tire per tire assembly (optional)
Position : 3
1 DECAL, Dashboard- LH used on Domestic Models
Position : 3
1 DECAL, Dashboard- LH- Euro
Position : 3
1 BRACKET, Regulator (not shown) B&S #
Position : 3
1 CLUTCH CABLE, Auger Drive- RH parts number is stamped on
Position : 4
1 ROD, Chute, Upper
Position : 4
1 END PLATE, LH- Auger Housing- Red
Position : 4
1 WING KNOB, 5/16-18
Position : 4
1 SET SCREW, 3/8-16 x 1/2” Square Head
Position : 4
1 WASHER, 3/8” Split Lock or
Position : 4
3 LOCKWASHER, 5/16” Exterior Tooth or
Position : 4
3 LOCKWASHER, 5/16” Exterior Tooth or
Position : 4
1 RIM, 6 x 3.25 (Weldment) per tire assembly
Position : 4
1 DECAL, Dash Front - SNAPPER
Position : 4
1 SCREW, Hex Head B&S #
Position : 4
1 HANDLE, Upper, Right Hand
Position : 5
1 CLIP, .093 Dia. Hair Pin
Position : 5
1 BLADE, Scraper- 22” replaces
Position : 5
1 BLADE, Scraper- 24” replaces
Position : 5
1 WIRE PIN
Position : 5
1 WELDMENT, Impeller
Position : 5
1 ASSEMBLY, Shift Arm w/Bushing includes weldment (1666213) &
Position : 5
1 TIRE, 15 x 5.00-6, 2 Ply, Carlisle Snow Hog per tire assembly
Position : 5
2 BOLT, 5/16-18 x 3/4” Hex Head Cap B&S #
Position : 5
1 GRIP, Clutch, RH
Position : 6
1 SPLICE, Chute Handle
Position : 6
2 BEARING, Auger
Position : 6
1 CHUTE RING
Position : 6
1 OIL SEAL
Position : 6
1 BUSHING, Spacer, .380 ID x .750 OD x 1.030 Long
Position : 6
1 HOSE, Oil Drain
Position : 6
2 ASSY, Tire and Wheel, 15 x 5.00-6 Carlisle Sno Hog includes items 2, 4
Position : 6
1 DECAL - Danger, Auger used on Domestic Models
Position : 6
1 DECAL, CE- Auger Warning used on European Models
Position : 6
1 CLIP, Speed B&S #
Position : 6
2 GRIP, Foam, Black
Position : 7
1 SPRING PIN, .156 x 1.000
Position : 7
1 RETAINER, Bearing
Position : 7
3 RETAINER, Spout
Position : 7
1 BUSHING
Position : 7
1 WASHER, 3/8” SAE Flat or
Position : 7
3 NUT, 5/16-18 Hex Flange Lock- small
Position : 7
1 DECAL, Stripe- SNAPPER (5hp, 22”)
Position : 7
1 DECAL, Stripe- SNAPPER (8hp, 24”) not shown; similar to above decal
Position : 7
1 DECAL, Stripe- SNAPPER (7.5hp, 22”) not shown; similar to above decal
Position : 7
1 DECAL, Stripe- SNAPPER (8.5hp, 24”) not shown; similar to above decal
Position : 7
3 HAIR PIN
Position : 8
1 ROD, Chute Lower
Position : 8
1 BALL BEARING
Position : 8
6 SCREW, #10-24 x 5/8” Hex Washer Self-Tap
Position : 8
1 PIN, Drive-Loc, 3/16 x 1-1/2”
Position : 8
1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5 or
Position : 8
1 NUT, 5/16-18 Hex Flange Lock
Position : 8
1 DECAL, Danger, Chute/Deflector
Position : 8
1 DECAL, Chute Warning
Position : 8
1 ROD, Shift, Lower
Position : 9
2 SKID SHOE, Reversible- Red or
Position : 9
3 BOLT, 5/16-18 x 5/8” Square Neck Carriage, GR
Position : 9
1 COLLAR, Thrust
Position : 9
4 SCREW, 5/16-18 x 5/8” Hex Head Cap, GR
Position : 9
1 ROD, Idler
Position : 9
2 NUT, 1/4-20 2B Hex
Position : 10
1 BRACKET, Universal Gear
Position : 10
4 WASHER, 3/8” Split Lock or
Position : 10
3 NUT, 5/16-18 Hex Flange Lock
Position : 10
1 SHAFT, Rolled Worm
Position : 10
2 BALL BEARING, .669 ID x .574 OD
Position : 10
2 ROLL PIN, 3/16 x 3/4” or
Position : 10
2 ROLL PIN, 3/16 x 3/4” or
Position : 10
1 DECAL, Lube- Controls
Position : 10
3 LOCKWASHER, 1/4” Spring
Position : 11
3 WASHER, .250 (.27 ID x .62 OD)
Position : 11
12 BOLT, 1/4-20 x 1/2” Short Square Neck Carriage, GR 5 or
Position : 11
1 BOLT, 5/16-18 x 3/4” Square Neck Carriage, GR
Position : 11
1 WASHER, Thrust (.562 ID x 1.000 OD x .030/.032 Thick)
Position : 11
2 RETAINER, Bearing
Position : 11
1 WELDMENT, Intermediate Frame- Red
Position : 11
1 DECAL, Sound
Position : 11
2 BOLT, 1/4-20 x 2” Short Square Neck Carriage, GR
Position : 12
2 RETAINER, 1/4” Bolt
Position : 12
3 SCREW, 5/16-18 x 5/8 Hex Head Cap, GR 5 or
Position : 12
2 WASHER, .34 x .69 x .08 Flat
Position : 12
1 FLANGE, Bushing
Position : 12
4 LOCKWASHER, 5/16” Spring or
Position : 12
6 SPEED NUT, 1/4-20 U-Type
Position : 12
6 SPEED NUT, 1/4-20 U-Type or
Position : 12
1 DECAL, Euro Community (CE)
Position : 12
1 ROD, Upper, Shift
Position : 13
2 BOLT, 1/4-20 x 5/8” Short Square Neck Carriage
Position : 13
12 NUT, 1/4-20 Hex Flange Lock Large
Position : 13
1 NUT, 5/16-24 Hex Center Lock, GR B
Position : 13
2 OIL SEAL
Position : 13
7 NUT, 5/16-18 Hex, GR B or 5 or
Position : 13
2 BUSHING, 1.00 long
Position : 13
1 DECAL, 2005 Year of Manufacture
Position : 13
2 BLOCK, Pivot
Position : 14
2 GEAR, Universal
Position : 14
4 BOLT, 3/8-16 x 3/4” Square Neck Carriage or
Position : 14
6 NUT 1/4-20 Hex replaces
Position : 14
1 HEX SHAFT
Position : 14
1 SUPPORT, Tie Bar
Position : 14
1 WELDMENT, Shift Rod Pivot
Position : 15
1 WASHER, 3/8” Flat- Black
Position : 15
4 WASHER, 3/8” Flat or
Position : 15
1 GEAR CASE, LH- Intermediate
Position : 15
1 RING, External Retaining (for 3/4 Dia Shaft)
Position : 15
2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap
Position : 15
1 SPRING, Compression
Position : 16
1 SPRING PIN, .125 x .750
Position : 16
4 NUT, 3/8-16 Hex Nyloc
Position : 16
1 GASKET, Gear Case
Position : 16
3 SCREW, 5/16-18 x 3/4” Hex Head Cap or
Position : 16
4 JAM NUT, 3/8-16 Hex Center Lock
Position : 16
1 COTTER PIN, .125 x 1.00
Position : 17
1 WORM SHAFT
Position : 17
6 SCREW, 5/16-18 x 1” Hex Washer Self-Tap
Position : 17
2 BUSHING
Position : 17
1 DRIVEN DISC or
Position : 17
3 WASHER, 3/8” Flat or
Position : 17
4 WASHER, 3/8” SAE Flat or 7090122 or
Position : 17
2 BUSHING, .500 ID x .750 OD x .25
Position : 18
2 NUT, 1/4-20 Hex Flange Lock
Position : 18
2 CAP, Bearing, Red
Position : 18
1 SHAFT, Auger, 22”/24”
Position : 18
1 HUB, Friction Disc
Position : 18
2 ROD, Belt Guide
Position : 18
1 WASHER, 1/2” Flat (.531 ID x 1.250 OD x .08 Thick)
Position : 19
1 ROLL PIN, 1/8 x 3/4”
Position : 19
3 WASHER, 5/16” Split Lock or
Position : 19
1 GEAR, Worm
Position : 19
2 COLLAR, Thrust
Position : 19
4 NUT, 3/8-16 Hex Nyloc Heavy Thin
Position : 19
1 WELDMENT, Shift Rod
Position : 20
1 WORM
Position : 20
5 BOLT, 1/4-20 x 7/16” Short Square Neck Carriage, GR
Position : 20
1 GEAR CASE, RH- Intermediate
Position : 20
1 PIN, Slide
Position : 20
1 SUPPORT, Frame
Position : 20
1 SCREW, 1/4-20 x 2-1/4” Hex Flange Lock
Position : 21
1 WASHER, .44 x .78 x .025 Curved
Position : 21
5 NUT, 1/4-20 Hex Flange Lock
Position : 21
1 PIPE PLUG, 1/8-27 NPTF 3/4 Taper x .31 Long Hex Drive
Position : 21
2 SET SCREW, 1/4-20 x 1/2 w/Patch Lock or
Position : 21
4 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap or
Position : 21
4 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap or
Position : 21
2 WASHER, .250 (.27 ID x .62 OD)
Position : 22
1 BRACKET, Worm
Position : 22
6 SCREW, 1/4-20 x 7/8” Hex Head Cap, GR
Position : 22
1 COLLAR, Set, 1.251 ID x 2.00 OD x .50 Long
Position : 22
1 SUPPORT, Pivot
Position : 22
1 KNOB, Tapered - 3/8-16 Internal Thread- Red
Position : 23
1 NUT, 5/16-18 Hex Flange Lock
Position : 23
1 FITTING, Grease
Position : 23
1 SPROCKET #35, 12 Tooth
Position : 23
2 WASHER, 5/16” Flat
Position : 23
1 WELDMENT, Dash
Position : 24
1 SCREW, 5/16-18 x 5/8” Hex Head Cap, GR
Position : 24
1 WELDMENT, 22” Auger, RH
Position : 24
1 WASHER, 1/4 ID x 5/8 OD x .134/.109 Flat or
Position : 24
3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or
Position : 24
3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or 1922127 (HHCS, 5/16-18 x 1-
Position : 24
1 HANDLE, Lower
Position : 25
1 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap
Position : 25
1 WELDMENT, 22” Auger, LH
Position : 25
1 LOCKWASHER, 1/4” Spring
Position : 25
1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or
Position : 25
1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or 1922127 (HHCS, 5/16-18 x 1-
Position : 25
2 SCREW, 5/16-18 x 2” Hex Head Cap, GR
Position : 25
2 WING KNOB, 5/16-18
Position : 26
2 COTTER PIN, 1/4” Self Locking replaces
Position : 26
1 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5 or
Position : 26
1 COVER, Bottom- Red
Position : 26
2 WASHER, 5/16” Internal Tooth Lock
Position : 27
2 SHEAR PIN, .248 ID x 1-3/4” Long
Position : 27
1 COLLAR, Set, .756 ID x 1.249 OD x .50
Position : 27
9 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap
Position : 27
4 NUT, 5/16-18 Hex Flange Nyloc
Position : 28
4 WASHER
Position : 28
2 SET SCREW, 5/16-18 x 1/2” Square Head Cup Point or
Position : 28
1 WASHER, 7/16” Flat
Position : 28
2 WASHER, .312 (.34 ID x .75 OD) or
Position : 29
2 RING, External Retaining (for .75 dia. Shaft)
Position : 29
1 WELDMENT, Axle & Sprocket
Position : 29
1 COTTER PIN, 1/8 x 3/4”
Position : 29
1 ASSEMBLY, Rod w/Pin includes items 31, 47, 54, 55 &
Position : 30
1 KEY, #605 Woodruff
Position : 30
1 CHAIN, Roller, #35, 25.5” Long
Position : 30
1 WELDMENT, Idler Arm
Position : 30
1 WELDMENT, Idler Arm
Position : 30
1 SPRING, Compression
Position : 31
1 TUBE, Low Density Polyethylene Extruded
Position : 31
1 BUSHING
Position : 31
1 BOLT, 3/8-16 x 1-1/4” Short Square Neck Carriage
Position : 31
1 PUSH NUT
Position : 32
12 FLAT WASHER, .268 ID x .591 OD x .063 Thick
Position : 32
1 PULLEY, Traction
Position : 32
1 SPACER, .377 ID x .75 OD x .312 Long
Position : 32
1 ROD, Hold Down
Position : 33
6 WASHER, 1/4” Split Lock
Position : 33
2 NUT, 5/16-18 Large Head Center Lock or
Position : 33
1 PULLEY, Idler
Position : 33
1 SCREW, 1/4-20 x 2” Hex Head Cap, GR
Position : 34
2 SPACER, .328 ID x .562 OD x .144/.149 Thick
Position : 34
1 BELT, V Groove, 4L Section; 36.00” nom. effective length Auger Drive
Position : 34
1 BELT, V Groove, 4L Sect.; 36.00” nom. effective length Auger Drive
Position : 34
1 GRIP, Clutch, LH
Position : 35
1 ASSY, Pivot Plate/Hub w/Bearing includes weldment (1726779),
Position : 35
1 BELT, V Groove, 3L Section; 35.25” effective length Traction Drive
Position : 35
1 V-BELT, 3L, 31.64 effective length Traction Drive
Position : 35
2 NUT, 1/4-20 Hex Centerlock
Position : 36
2 SCREW, 5/16-18 x 5/8 Hex Head Cap, GR 5 or
Position : 36
1 SPRING, Extension
Position : 36
2 SPACER, Handle
Position : 37
1 WASHER
Position : 37
1 PAD, Brake
Position : 37
1 HANDLE, Upper, Left Hand
Position : 38
1 KEY, Hi-Pro, #HP-506 or
Position : 38
2 RIVET, Blind
Position : 38
2 SCREW, 1/4-20 x 1-1/2” Hex Head Cap
Position : 39
1 DRIVE DISC, w/ Spindle
Position : 39
1 ASSEMBLY, Idler Arm w/Brake Pad includes idler arm weldment
Position : 39
1 ASSEMBLY, Idler Arm w/Brake Pad incl. items 37, 38 &
Position : 39
2 SPACER, .268 ID x .394 x .165
Position : 40
1 ROD, Pivot
Position : 40
1 BOLT, 3/8-16 x 1-3/4 Short Square Neck Carriage, GR
Position : 40
2 SCREW, 1/4-20 x 3/4” Pan Head Torx Self-Tap
Position : 41
1 COTTER PIN, 1/8 x 3/4”
Position : 41
1 WASHER, 3/8” Flat (.41 ID x 1.00 OD x .13 Thick)
Position : 41
5 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR
Position : 42
1 NUT, 5/16-18 Hex Nyloc Light or
Position : 42
1 PULLEY, Idler
Position : 42
1 LEVER, Pivot
Position : 43
2 WASHER, .312 (.34 ID x .75 OD) or
Position : 43
1 COVER, Belt
Position : 43
2 NUT, 1/4-20 Hex Nyloc
Position : 44
1 BELLCRANK
Position : 44
1 SPRING, Idler- Extension
Position : 44
1 SPRING, Extension, .562 O.D. x 4.250 Long
Position : 44
1 SNOW STICK
Position : 45
1 BUSHING
Position : 45
1 JAM NUT, 5/16-24 Hex
Position : 45
1 JAM NUT, 5/16-24 Hex or
Position : 45
1 NUT, #10-24 Hex Center Lock
Position : 46
1 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 or
Position : 46
1 KEY - Hi Pro .125 x .625 HP 504 SAE1035
Position : 46
1 ROD, Hand Control not shown; part of item
Position : 47
1 WASHER, Plain, .75 ID x 1.31.OD x .10
Position : 47
1 PULLEY, V Groove
Position : 47
1 HOLDER, Snostik- Upper
Position : 48
1 COTTER PIN, 3/8” Self Lock
Position : 48
2 SET SCREW, 5/16-18 x 5/16” Hex Recess, Cup Point
Position : 48
2 SET SCREW, 5/16-18 x 5/16” Hex Recess, Cup Point or
Position : 48
1 CLUTCH CABLE, Ground Drive- LH parts number is stamped on
Position : 49
1 PULLEY, 2.75 OD
Position : 49
4 BOLT, 5/16-18 x 2” Curved Head Square Neck GR
Position : 50
1 KEY, 3/16 Square x 1”
Position : 50
1 KEY, 3/16 Square x 1” or
Position : 50
1 WASHER, #10 Internal Tooth Lock
Position : 51
1 HARNESS CLIP
Position : 51
1 SCREW, #10-24 x 2” Hex Washer Head Machine, GR
Position : 52
1 NUT, 3/8-16 Hex Flange Lock Two Way
Position : 52
1 CORD, Electric Start
Position : 52
4 LOCKWASHER, Spring .312 or
Position : 53
1 MUFFLER GUARD, Domestic (Tecumseh)
Position : 53
1 GUARD, Muffler
Position : 53
1 BUSHING, .250 ID x .375 OD x .750 not shown; part of item
Position : 54
1 SCREW, #10-24 x 5/8” Hex Washer Self-Tap
Position : 54
1 MUFFLER, Deflector- B&S Briggs p/n
Position : 54
1 PIN, Clevis not shown; part of item
Position : 55
1 MUFFLER GUARD, Tecumseh Engine (Euro) not shown; Tecumseh p/n 127-
Position : 55
1 HEX SCREW, Thread Rolling M4 x 0.7 Briggs p/n
Position : 55
1 SPRING, Compression not shown; part of item
Position : 56
2 SCREW. Tecumseh Muffler not shown; Tecumseh p/n 42-
Position : 56
2 LOCK WASHER, Tecumseh Muffler not shown; Tecumseh p/n 36-
Position : 57
1 HEAT SHIELD, 7.5HP B&S Powerbuilt Muffler used on I75225 model
Position : 57
2 WASHER, Tecumseh Muffler not shown; Tecumseh p/n 36-
Position : 58
1 SCREW, 5/16-24 x 1” Hex Head Cap, GR
Position : 58
1 SCREW, 5/16-24 x 1-1/2” Hex Head Cap, GR
Position : 59
8 WASHER, 5/16” Flat
Position : 60
1 BUSHING, Differential Link
Position : 61
5 WASHER, 5/16” Split Lock
Position : 62
4 NUT, 5/16-18 Hex, GR 5 or B
Position : 63
2 WASHER, 5/16” Internal Tooth Lock
Position : 64