Assistant réparation
Assistant IA
Liste des pièces détachées
1 SHAFT, Cross
Position : 1
2 WHEEL & TIRE ASSEMBLY, 18 x 8-1/2-8
Position : 1
4 NUT, Hex Jam, 7/16-14, NC-2B
Position : 1
4 BOLT, Shoulder (Gauge Wheel) 3/8-16 x 2.781 x 3/4
Position : 1
2 NUT, Hex Nylock, 5/8
Position : 1
1 V-BELT, Arbor Drive, 91.1 Kevlar
Position : 1
3 NUT, Hex Flange, 9/16-18
Position : 1
1 DECAL, Danger Do Not Operate without Deflector
Position : 1
2 SWITCH, Push Button
Position : 1
4 WASHER, 3/4 ID x 1.6 OD x .05 THK
Position : 2
4 WASHER, .34 ID x 1 OD x .13 THK
Position : 2
2 WASHER, 1/2
Position : 2
1 LOCKWASHER, Spring
Position : 2
2 CAPSCREW, Hex Head
Position : 2
2 TRUNNION
Position : 2
4 WASHER, .51 ID x 1 OD x 1/10 THK
Position : 2
2 PULLEY, Drive, 5-1/2
Position : 2
1 V-BELT, P.T.O. Drive, 73.24 A-Wedge
Position : 2
6 WASHER, Belleville
Position : 2
1 DECAL, Danger Do Not Put Hands/Feet in Mower
Position : 2
1 SWITCH ASSEMBLY, Ignition, 5/8-32 6 Pin Indak (Includes Ref. Nos. 20, 21, 26, &
Position : 2
2 RING, Klipring, 3/4
Position : 3
2 SPACER
Position : 3
2 RING, Klipring Extension
Position : 3
2 CAPSCREW, Hex Head, 5/16-18 x 3/4, G8
Position : 3
1 WASHER, Hex, 7/16
Position : 3
2 TUBE, Caster Wheel Spacer
Position : 3
1 ROD, Bail
Position : 3
4 GAUGE WHEEL
Position : 3
2 SPACER, Pulley
Position : 3
1 CAPSCREW, Hex Head, 3/8-16 x 3-1/4, G5
Position : 3
1 PULLEY, Deep Groove, 4.5
Position : 3
1 DECAL, 42"
Position : 3
1 DECAL, 50"
Position : 3
1 LOCKWASHER, Internal Tooth, 5/8 Thin
Position : 3
2 CAP, Hub
Position : 4
2 NUT, Hex Keps, 5/16-18
Position : 4
5 CAPSCREW, Hex Head, 5/16-18 x 1-1/4, G5
Position : 4
2 LOCKWASHER, Spring, 5/16
Position : 4
1 TIE, Self-Locking, 3.62"
Position : 4
2 WHEEL & TIRE ASSEMBLY, 11 x 4-5
Position : 4
4 RING, Retaining, 1-3/4
Position : 4
5 WASHER, Flat, 3/8
Position : 4
1 HUB, Spacer
Position : 4
1 NUT, Hex Flange, 5/8-32 IGN SW Die Cast
Position : 4
2 BUSHING, Axle Pivot
Position : 5
1 ROD, Control L.H.
Position : 5
6 NUT, Hex Jam, 5/16-18
Position : 5
1 PIPE ASSEMBLY, Exhaust
Position : 5
1 CLUTCH, Electric Ogura
Position : 5
2 NUT, Hex Center Lock
Position : 5
2 BOLT, Shoulder
Position : 5
4 NUT, Hex Flange, 3/8-16 ESNA
Position : 5
4 BEARING, Spindle
Position : 5
1 PULLEY, 4-1/2 OD 3/8 ID .63 Groove
Position : 5
3 PULLEY
Position : 5
2 DECAL, Simplicity Logo
Position : 5
1 COVER, Ignition Switch
Position : 5
1 AXLE, Casting (Includes Ref. Nos. 1, 2, 3, 4 & 5)
Position : 6
1 ROD, Control R.H.
Position : 6
2 NUT, Speed, 5/16-18 Lug Type
Position : 6
1 GASKET, Exhaust
Position : 6
2 FITTING, Lube
Position : 6
5 NUT, Hex Whiz Lock Flange, 5/16-18
Position : 6
1 SPACER
Position : 6
1 HUB
Position : 6
1 DECAL, Operator Instructions Front
Position : 6
2 KEYS (Set of Two)
Position : 6
2 BOLT, Shoulder, G5
Position : 7
2 BOLT, Shoulder
Position : 7
15 NUT, Hex Flange, 5/16-18 ESNA
Position : 7
4 SCREW, Hex Whiz Lock Flange, 1/4-20 x 5/8
Position : 7
1 WASHER, 3/8
Position : 7
2 VALVE STEM & CAP
Position : 7
4 NUT, Hex Whiz Lock Flange, 3/8-16
Position : 7
2 LUBE, Fitting, 1/4
Position : 7
1 ARM ASSEMBLY, Idler with Bushings
Position : 7
2 HUB
Position : 7
1 DECAL, Operator Instructions Back
Position : 7
1 HOUR METER, No Alarms
Position : 7
3 NUT, Hex Flange, 3/8-16 ESNA
Position : 8
6 NUT, Hex Flange Two-Way Lock, 7/16-14
Position : 8
4 NUT, Hex Whiz Lock Flange, 5/16-18
Position : 8
8 NUT, Hex Lug, 7/16-20
Position : 8
2 PIN, Threaded Shoulder
Position : 8
2 SHAFT, Spindle
Position : 8
1 CARRIAGE BOLT, 3/8-16 x 1-3/4, G5
Position : 8
1 DECAL, Handle Control R.H. Simplicity
Position : 8
1 PLUG, Hole
Position : 8
1 CAPSCREW, Hex Head, 5/8-11 x 3-1/4, G5
Position : 9
4 CAPSCREW, Hex Head, 7/16-14 x 2-1/4, G8
Position : 9
2 CLIP, Brake
Position : 9
1 SPACER
Position : 9
2 WASHER, 1/2"
Position : 9
1 SPRING, Extension
Position : 9
3 BEARING
Position : 9
1 DECAL, Tracking Adjustment
Position : 9
1 SWITCH, PTO Push/Pull Symbols
Position : 9
1 WASHER, 5/8, .64 ID x 1-3/4 OD x .11 THK
Position : 10
4 CAPSCREW, Hex Head, 5/16-18 x 2-3/4, G5
Position : 10
1 BRACKET, Muffler/Heat Shield
Position : 10
4 CLIP, Hair Pin
Position : 10
2 WASHER, Spindle Blade, Powdered Metal
Position : 10
1 SPACER, Powdered Metal
Position : 10
3 SPACER, Bearing Sleeve
Position : 10
1 DECAL, Model 150Z, 20HP
Position : 10
1 DECAL, Model 150Z, 24HP
Position : 10
4 TIE, Self Locking, .184 WD 7.31 LG
Position : 10
1 NUT, Hex Flange Two-Way Lock, 5/8-11
Position : 11
6 WASHER, .34 ID x 3/4 OD x .06 THK
Position : 11
8 CARRIAGE BOLT, 5/16-18 x 1, G5
Position : 11
1 SPACER, .390 ID x .9 OD x .34 LG, Powdered Metal
Position : 11
2 NUT, Hex Whiz Lock Flange, 5/16-18
Position : 11
2 RING, Klipring, 5/8"
Position : 11
17 NUT, Hex Flange Whiz Lock, 5/16-18
Position : 11
2 BLADE, 19.64
Position : 11
1 PULLEY, Idler Flat
Position : 11
3 SPACER, Powdered Metal
Position : 11
1 DECAL, Height of Cut
Position : 11
1 SWITCH, Push Button
Position : 11
2 CARRIAGE BOLT, 5/16-18 x 1-3/4, G5
Position : 12
1 CAPSCREW, Hex Head, 5/16-18 x 1-1/4, G5
Position : 12
4 SCREW, Hex Washer Head Taptite, 5/16-18 x 1/2
Position : 12
2 NUT, Hex Flange, 3/8-16 ESNA
Position : 12
1 NUT, Hex Two-Way Lock, 5/16-18
Position : 12
4 WASHER, Belleville
Position : 12
4 NUT, Hex Flange Lock, 3/8-16
Position : 12
3 GASKET, Foam
Position : 12
1 DECAL, Belt & Blade
Position : 12
1 BRACE, Battery, .19 DIA Wire
Position : 12
2 SCREW, Hex Head Taptite, 5/16-18 x 5/8
Position : 13
1 CLIP, Rod End Linkage
Position : 13
1 MUFFLER ASSEMBLY, Single
Position : 13
2 CAPSCREW, Hex Head, 5/16-18 x 3/4, G5
Position : 13
2 SPACER
Position : 13
1 CARRIAGE BOLT, 5/16-18 x 1-3/4, G5
Position : 13
2 NUT, Hex, 9/16
Position : 13
1 SPACER, Idler Powdered Metal
Position : 13
3 BEARING, Ball
Position : 13
1 DECAL, Instrument Panel
Position : 13
1 STRAP, Black Rubber, .19 SQ 7.88 OD Battery
Position : 13
2 NUT, Speed Lug Type, 1/4-20
Position : 14
1 ROD, Tow Valve L.H.
Position : 14
4 LOCKWASHER, Spring, 5/16
Position : 14
1 CAPSCREW, Hex Head, 5/16-18 x 1-1/2, G5
Position : 14
2 TRUNNION
Position : 14
16 CARRIAGE BOLT, 5/16-18 x 3/4, G5
Position : 14
1 SPRING, Extension
Position : 14
1 DECAL, Warning Burn Hazard (24HP Models Only)
Position : 14
1 BATTERY, 12 Volt 6 Cell 230 CCA
Position : 14
8 SCREW, Truss Head Torx, 1/4-20 x 3/4
Position : 15
1 CARRIAGE BOLT, 3/8-16 x 1-1/4, G5
Position : 15
4 SCREW, Truss Head Torx Drive, 5/16-18 x 7/8
Position : 15
1 HOSE, Oil Drain, 16.5"
Position : 15
2 ROD, Mower Lift 3/8-16 x 1 LG Thread
Position : 15
2 NUT, Hex Flange Whiz Lock, 3/8-16
Position : 15
2 PLATE, Rear
Position : 15
31 SCREW, Hex Washer Head Taptite, 5/16-18 x 3/4
Position : 15
1 DECAL, Seat Deck R.H. Snapper
Position : 15
2 CAPSCREW, Hex Head, 1/4-20 x 3/4, G5
Position : 15
1 CARRIAGE BOLT, 1/2-13 x 1-1/2, G5
Position : 16
6 WASHER, 5/16
Position : 16
4 CAPSCREW, Thread Cutting, # 10 x 1/2
Position : 16
1 SPRING, Extension
Position : 16
6 NUT, Hex Flange, 5/16-18 ESNA
Position : 16
2 WASHER, Flat, 3/8
Position : 16
1 DECAL, Seat Deck L.H. Snapper
Position : 16
2 WASHER, 1/4, .27 ID x .62 OD x .05 THK
Position : 16
14 NUT, Hex Flange, 1/4-20 ESNA
Position : 17
2 CLAMP, Saddle Snow Handle, E-Coat
Position : 17
1 SEAL, Foam Air Inlet
Position : 17
1 SPACER, Powdered Metal
Position : 17
1 BRACKET, Hinge
Position : 17
1 CAPSCREW, Hex Head, 3/8-16 x 1-1/4, G5
Position : 17
2 SHAFT, Arbor Short
Position : 17
1 DECAL, Height of Cut w/out Best Cut
Position : 17
2 LOCKWASHER, Spring, 1/4
Position : 17
2 CARRIAGE BOLT, 1/4-20 x 3/4, G5
Position : 18
2 CAPSCREW, Hex Head, 5/16-18 x 2-1/2, G5
Position : 18
2 TIE, Self Locking, 3-5/8 LG
Position : 18
1 THROTTLE ASSEMBLY
Position : 18
1 SPACER, Powdered Metal
Position : 18
5 CARRIAGE BOLT, 5/16-18 x 3/4, G5
Position : 18
1 PULLEY, Idler
Position : 18
1 SHAFT, Arbor Long
Position : 18
2 DECAL, Transmission Release Instructions
Position : 18
2 NUT, Hex, 1/4-20 NC-2B
Position : 18
1 PAD, Footrest Panel
Position : 19
1 CLIP, Rod End Linkage
Position : 19
2 GRIP, Foam Handle
Position : 19
1 HOSE, Oil Drain, 16-1/2 LG
Position : 19
1 CARRIAGE BOLT, 5/16-18 x 1-1/2, G5
Position : 19
1 WASHER, 3/8, .41 ID x 1-1/2 OD x 1/4 THK
Position : 19
10 SCREW, Hex Washer Head Taptite, 3/8-16 x 3/4
Position : 19
1 CARRIAGE BOLT, 3/8-16 x 1-1/4, G5
Position : 19
3 SHIELD, Grass
Position : 19
1 DECAL, Do Not Remove Foam Around Engine
Position : 19
1 BOOT, Insulator, Red PVC Warning
Position : 19
1 SEAT ASSEMBLY, with Armrests
Position : 20
1 ROD, Tow Valve R.H.
Position : 20
3 SCREW, Hex Washer Head Taptite, 3/8-16 x 1-1/4
Position : 20
2 PULLEY, Idler, 4 OD x .378 ID x
Position : 20
1 SPRING, Torsion
Position : 20
4 WHEEL, 2" WIDE, 3.92 DIA
Position : 20
3 BLADE, Mower, 50" Deck
Position : 20
1 DECAL, Handle Control, L.H.
Position : 20
1 CABLE, # 6 x 10 LG, Red Two-Ring Terminals
Position : 20
6 NUT, Hex Flange Whiz Lock, 5/16-18
Position : 21
1 PULLEY ASSEMBLY, Engine
Position : 21
1 HEAT SHIELD, Throttle
Position : 21
1 NUT, Hex, 1/4-20 L.H. Thread
Position : 21
2 WASHER, 3/8, .41 ID x .87 OD x .08 THK
Position : 21
1 DEFLECTOR ASSEMBLY
Position : 21
4 BOLT, Wheel, 3/8-16 x 2.781
Position : 21
1 CABLE, # 6 X 26 LG, Two-Ring Terminals
Position : 21
2 NUT, Push, 1/4
Position : 22
8 NUT, Wheel Hex, 1/2-20
Position : 22
4 CAPSCREW, Hex Head, 5/16-18 x 1-1/2, G5
Position : 22
1 KEY, Hi-Pro, 1/4 x 2-1/2
Position : 22
4 NUT, Speed, 1/4-20
Position : 22
1 WASHER, 1/4"
Position : 22
2 CAPSCREW, Hex Head, 3/8-16 x 2-1/4, G5
Position : 22
1 ROD, Deflector
Position : 22
4 WASHER, Flat, 1/2
Position : 22
3 WASHER, Hex, 11/16 x
Position : 22
1 CABLE, # 6 x 15 LG, Two-Ring Terminals
Position : 22
4 NUT, Speed Lug Type, 5/16-18
Position : 23
2 SHOCK ABSORBER
Position : 23
1 CLUTCH, Electric
Position : 23
1 HEAT SHIELD, Muffler Side
Position : 23
1 MOTOR, Mini Actuator
Position : 23
2 NUT, Pushpal
Position : 23
4 NUT, Hex Flange, 3/8-16 ESNA
Position : 23
3 WASHER, Spring
Position : 23
3 COVER, Terminal Red PVC
Position : 23
2 BOLT, Shoulder
Position : 24
1 TRANSMISSION, Hydro Gear EZT L.H.
Position : 24
1 WASHER, Hex, .453 ID x 1-1/2
Position : 24
1 MUFFLER, 24HP V-Twin ELS
Position : 24
3 PIN, Quick
Position : 24
1 CAPSCREW, Hex Head, 5/16-18 x 1, G5
Position : 24
3 CAPSCREW, Hex Head, 7/16-14 x 1-1/4, G8
Position : 24
1 BREAKER, Circuit, 12 Volt 20 AMP
Position : 24
2 CARRIAGE BOLT, 5/16-18 x 1-1/4, G5
Position : 25
1 TRANSMISSION, Hydro Gear EZT R.H.
Position : 25
4 NUT, Hex Lock ESNA Light, 5/16-18NC-3B
Position : 25
1 LOCKWSHER, Spring, .438
Position : 25
4 CAPSCREW, Hex Head, 5/16-18 x 3/4, G8
Position : 25
1 ROD, Height of Cut Indicator
Position : 25
6 NUT, Hex Whiz Lock Flange, 5/16-18
Position : 25
1 WIRE, 12 Gauge, 7.9 LG
Position : 25
2 PIVOT, Hood, Powdered Metal
Position : 26
1 WASHER, 5/16
Position : 26
1 CAPSCREW, Hex Head, 7/16-20 x 2-3/4, G5
Position : 26
1 INDICATOR, Height of Cut
Position : 26
6 CARRIAGE BOLT, 5/16-18 x 3/4, G5
Position : 26
1 SOLENOID, Two Terminals, Trombetta
Position : 26
8 NUT, Hex Flange Whiz Lock, 5/16-18
Position : 27
3 NUT, Hex Flange, 3/8-16 ESNA
Position : 27
4 SPACER, Powdered Metal
Position : 27
2 GASKET, Exhaust
Position : 27
2 NUT, Hex Two-Way Lock, 1/2-13
Position : 27
1 V-BELT, A-Wedge, 98.00
Position : 27
2 SCREW, Hex Washer Head Taptite, 1/4-20 x 1/2
Position : 27
2 BOLT, Shoulder, G5
Position : 28
1 NUT, Hex Flange, 1/2-13
Position : 28
2 CARRIAGE BOLT, 5/16-18 x 2-1/4, G5
Position : 28
2 WASHER, 5/16, .34 ID x 3/4 OD x .06 THK
Position : 28
1 DECAL, Hot Exhaust
Position : 28
1 CARRIAGE BOLT, 5/16-18 x 1, G5
Position : 28
2 WASHER, Belleville
Position : 28
3 WASHER, Cup
Position : 28
1 SWITCH, Electric Height of Cut
Position : 28
6 SCREW, Hex Whiz Lock Flange, 1/4-20 x 5/8
Position : 29
1 BOLT, Shoulder
Position : 29
1 HEAT SHIELD
Position : 29
1 CABLE, Choke
Position : 29
1 PIN, Shear
Position : 29
1 COVER, Arbor
Position : 29
2 NUT, Hex Keps, 5/16-24
Position : 29
2 SCREW, Hex Flange Whiz Lock, 5/16-18 x 3/4 Dog PT
Position : 30
1 WASHER, .34 ID x .87 OD x .06 THK
Position : 30
2 RIVET, Pop
Position : 30
1 COVER, Arbor
Position : 30
1 HARNESS, Wiring
Position : 30
1 SCREEN, Seat Deck
Position : 31
1 NUT, Hex Flange, 5/16-18
Position : 31
2 CARRIAGE BOLT, 3/8-16 x 3/4, G5
Position : 31
1 PLUG, Hole
Position : 31
1 CABLE, Clip
Position : 31
3 RIVET, Pop
Position : 32
2 WASHER, 3/8
Position : 32
1 WASHER, 3/8, .41 ID x .87 OD x .08 THK
Position : 32
2 SCREW, Taptite Pan Head Torx, 1/4-20 x 5/8
Position : 32
1 CARRIAGE BOLT, 1/4-20 x 7/8, G5
Position : 32
1 V-BELT, Transmission Drive, 54.4
Position : 33
1 RETAINER, Clutch
Position : 33
1 SCREW, Taptite Pan Head Combo, #10-16 x 3/4
Position : 33
2 NUT, Hex 3/8 -
Position : 33
2 NUT, Push On
Position : 33
1 NUT, Hex Whiz Lock Flange, 5/16-18
Position : 33
2 NUT, Hex Flange Two-Way Lock, 3/8-16
Position : 34
4 BUSHING
Position : 34
2 CARRIAGE BOLT, 1/4 - 20 x 3/4
Position : 34
4 WASHER, 1/4
Position : 34
1 SEAT DECK, Plastic
Position : 35
2 WASHER, .41 ID x 1-1/2 OD x .12 THK
Position : 35
1 SPRING, Compression
Position : 35
1 SEAL, Foam Air Duct, 1 x 2-1/2, 12" LG
Position : 35
1 HOSE, Fuel, 19.5" (See Frame, Body & Seat Group
Position : 35
2 NUT, Hex Flange Whiz Lock, 1/4 -
Position : 35
1 CLAMP
Position : 35
1 WASHER, 5/16, .34 ID x 3/4 OD x .06 THK
Position : 35
2 CAPSCREW, Hex Head, 3/8-16 x 1, G5
Position : 36
1 KNOB, Extension Thread, 5/16-18 x 1-1/4
Position : 36
2 WASHER, 3/8
Position : 36
1 CAPSCREW, Hex Head, 5/16-18 x 2, G5
Position : 36
6 SCREW, Truss Head Torx, 1/4-20 x 3/4
Position : 37
1 SPRING, Extension
Position : 37
1 BUSHING, Powdered Metal
Position : 37
5 SCREW, Hex Whiz Lock Flange, 5/16-18 x 3/4
Position : 38
1 SPACER, Powdered Metal
Position : 38
1 BRACKET, Pivot
Position : 38
1 PAD, Footrest R.H.
Position : 39
1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4, G5
Position : 39
1 DEFLECTOR, Discharge
Position : 39
1 PAD, Footrest L.H.
Position : 40
1 PULLEY, Idler Flat
Position : 40
4 PIN, Quick
Position : 40
1 SPRING, Torsion Chute
Position : 40
2 WASHER, .41 ID x .87 OD x .08 THK
Position : 41
2 WASHER, 1/4
Position : 41
1 ROD, Deflector, Front
Position : 41
1 ROD, Pivot
Position : 42
1 CAPSCREW, Hex Head, 5/16-18 x 3/4, G5
Position : 42
3 NUT, Hex Lock ESNA, 1/4-20
Position : 42
1 ELBOW, Gas Tank
Position : 43
2 CAPSCREW, Hex Head, 3/8-16 x 2, G5
Position : 43
1 ROD, 1/4-20 x
Position : 43
1 CABLE, Choke
Position : 43
1 CARRIAGE BOLT, 1/4-20 x 1-1/2, G5
Position : 43
1 BUSHING, Fuel
Position : 44
1 NUT, Push Pal, 3/8
Position : 44
1 SPRING, Extension
Position : 44
1 WASHER, Lock Internal Tooth, 3/8
Position : 44
1 CAPSCREW, 5/16, 18 x 1-1/2
Position : 45
1 NUT, Push Pal, 1/2
Position : 45
1 NUT, Hex, 3/8
Position : 45
1 WASHER, 5/16, .34 ID x 1 OD x .13 THK
Position : 46
2 NUT, Hex Head Center Lock
Position : 46
1 SPRING, Compression
Position : 46
1 CONTROL, Throttle
Position : 46
1 LOCKWASHER, External Tooth, 3/8
Position : 47
2 PULLEY, 4-1/2" Transmission
Position : 47
1 NUT, Hex Flange, 1/4-20 ESNA
Position : 47
2 SCREW, Pan Head Taptite Torx, 1/4-20 x 5/8
Position : 47
1 SPACER, .33 ID x 1/2 OD x 5/16 LG
Position : 48
2 FAN, 6" Transmission
Position : 48
2 SCREW, Hex Washer Head Taptite, 1/4-20 x 1/2
Position : 48
1 SCREW, Pan Head Taptite Combo, 310-16 x 3/4
Position : 48
1 TANK, Fuel
Position : 49
1 PARKING BRAKE ARM ASSEMBLY, Transmission
Position : 49
1 KNOB, Throttle
Position : 49
1 CAP, Fuel Tank
Position : 50
1 HYDRO SEAL KIT
Position : 50
1 HOSE, Fuel, 19.5" (See Frame, Body & Seat Group
Position : 50
5 CAPSCREW, Hex Head, 5/16-18 x 1-1/4, G5
Position : 51
2 HUB REPLACEMENT KIT
Position : 51
2 CLAMP, Hose
Position : 51
4 NUT, Push Pal, 5/16 DIA Thread, 5/8 OD
Position : 52
2 HUB, EZT Transmission
Position : 52
2 NUT, EZT Transmission
Position : 53
2 BUMPER, Rubber
Position : 54
1 GEAR, Parking Brake, Transmission
Position : 54
1 CLIP, E Transmission Parking Brake
Position : 55
6 SCREW, Hex Washer Head Taptite, 1/4-20 x 1/2
Position : 56
1 ARM, Control Kit L.H.
Position : 56
1 ARM, Control Kit R.H.
Position : 57
1 ARM REST KIT, L.H. & R.H.
Position : 58
2 SPRING, Extension (Used only on Hydro Gear P/N
Position : 58
2 SPRING, Extension (Used only on Hydro Gear P/N
Position : 58
5 NUT, Hex Flange Nylock, 5/16-18
Position : 59
1 KEY, Ignition Indak (Not shown) Set of Two
Position : 1717163
1 LITERATURE PACK, Snapper ZT 20/42 (Not shown)
Position : 1734233
1 LITERATURE PACK, Snapper 24/50 (Not shown)
Position : 1734234